2019年拆装实习报告怎样写

《2019年拆装实习报告怎样写》由会员上传分享，免费在线阅读，更多相关内容在应用文档-天天文库。

1、拆装实习报告怎样写篇一：拆装实习报告实习地点机械工程学院实习时间201x年7月4日-7日学院机械工程学院班级车辆工程0812姓名学号20XX715051指导老师刘长寿胡景煌陈宁林开荣成绩201x年7月8日目录一、实习目的意义及注意事项·····························································1（一）实习目的····················································································1（二）实习要求

2、····················································································1（三）实习设备和工具·········································································3（四）注意事项····················································································3二、实习内容···········

3、·············································································5（一）拆装前的准备工作·····································································5（二）变速器的拆装·············································································5（三）后桥的拆装························

4、·························································7（四）发动机外部各装置、机件的拆卸··············································9（五）发动机的拆卸···········································································10（六）发动机总体安装····························································

5、···········14三、实习结果······················································································15四、实习总结与体会···········································································17篇二：拆装实习报告(模板)汽车拆装实习报告汽车系别：专业：班级：学号：姓名：工程汽车工程车辆工程07级4班20XX30855216欧清海系实验中心发动机拆装实习报告实习日

6、期：指导老师：成绩：一、实习目的与要求通过实训让同学们了解发动机的基本结构以及它的拆装顺序和操作规程(于:.zaIdian.cOM在点网)，让同学对汽车的动力源的主要部件总成有个初步的认识和了解。二、设备（所拆发动机型号）及常用工具和仪器设备：宝马M30B35型发动机工具和仪器：T柄、套筒扳手、开口扳手、钳、T型套筒、卡环钳、尖嘴钳、活动扳手、机油滤清器拆装工具、螺丝批、锤子、两端开口扳手、快速扳手以及加长杆、套筒、铜棒。三、实习内容1.发动机拆卸、认识发动机各部件构成、掌握二大机构、五大系统的工作原理。2.发动机装配（特别注意各部件的装配关系和顺序

7、，检查各原装配标记是否正确，如不正确装配时重新调整）。3.发动机调整,使各系工作处于正常工作状态。（如点火正时的调整、气门间隙调整等）四、拆装要点及大致拆装步骤和注意事项操作要点：操作规范，学会正确使用拆装设备及工具、量具；掌握正确的拆卸、安装顺序和方法；注意各装配标记，确保安装关系正确。做到先拆后装，后拆先装：拆前——观察、记忆；拆卸——顺序摆放、记忆；装配——倒顺序，回忆。注意事项：1、总成分解时，必须使用专用工具、机具按照分解顺序进行；对于较难拆的零件，必须采用合理有效的方法，不得违反操作规程，确保零件完好无损。2、对于螺纹连接件的拆卸，优先使

8、用套筒或梅花扳手，再有必要时才用开口扳手。3、对于专用工具应合理选用，不能超量程使用工具，确保工具完好安全。