dl905-2004t汽轮机叶片焊接修复技术导则

dl905-2004t汽轮机叶片焊接修复技术导则

ID:8077865

大小:94.63 KB

页数:7页

时间:2018-03-05

dl905-2004t汽轮机叶片焊接修复技术导则_第1页
dl905-2004t汽轮机叶片焊接修复技术导则_第2页
dl905-2004t汽轮机叶片焊接修复技术导则_第3页
dl905-2004t汽轮机叶片焊接修复技术导则_第4页
dl905-2004t汽轮机叶片焊接修复技术导则_第5页
资源描述:

《dl905-2004t汽轮机叶片焊接修复技术导则》由会员上传分享,免费在线阅读,更多相关内容在学术论文-天天文库

1、DL/T905—2004ICS27.100F23备案号:15174–2005中华人民共和国电力行业标准DL/T905—2004汽轮机叶片焊接修复技术导则Technicalguideforrepairweldingofturbineblades2004-12-14发布2005-06-01实施中华人民共和国国家发展和改革委员会发布IDL/T905—2004目次前言·················································································································

2、·············································Ⅱ1范围·······································12规范性引用文件········································································································································13一般规定·······················································

3、····························································································14母材、焊接材料与焊接设备·····················································································································25焊接工艺·································································

4、··················································································26质量检验···················································································································································37焊缝返修·····················································

5、······························································································48技术文件···················································································································································4IIDL/T905—2004前言本标准是根据原国家经济贸易委员会《关于确认2001年度电力行

6、业标准制、修订计划项目的通知》(电力[2001]44号文)的安排编制的。本标准主要是根据电力行业火电厂多年来有关汽轮机叶片损伤采用焊接方法修复的研究成果以及积累的经验编写的,对火力发电厂汽轮机叶片修复工作所涉及的焊接和热处理人员的资格、设备及工艺、技术措施、质量与安全等方面做出了具体规定。本标准由中国电力企业联合会提出。本标准由电力行业电站焊接标准化技术委员会归口并解释。本标准起草单位:国电电力建设研究所、山东电力研究院、华北电网有限公司焊接技术培训中心、河北电力研究院、江苏电力建设第一工程公司、宁夏电力科技教育工程院。本标准主要起草人:徐德录、张忠文、任永宁、姜运健、张学诚、马彦

7、喜、郭军。本标准为首次发布。IIIDL/T905—2004汽轮机叶片焊接修复技术导则1范围本标准规定了汽轮机叶片焊接修复的技术条件及其验收要求。本标准适用于火力发电厂采用焊条电弧焊、手工钨极氩弧焊方法从事汽轮机叶片的焊接修复,也适用于汽轮机叶片围带及拉筋的焊接修复。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。