大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc

大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc

ID:56730206

大小:1.50 MB

页数:25页

时间:2020-07-06

大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc_第1页
大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc_第2页
大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc_第3页
大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc_第4页
大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc_第5页
资源描述:

《大学本科机械设计课程设计,(葡萄收获机的传动部分),绝对的原创!.doc》由会员上传分享,免费在线阅读,更多相关内容在教育资源-天天文库

1、.目录1设计任务····················································11.1已知条件·····························································11.2设计要求·····························································11.3设计示意图···············································

2、············12电机选择····················································12.1各传动效率的确定······················································22.2各主要功率的计算·····················································22.3各传动比及其分配·········································

3、············23带轮皮带的设计··············································34直齿圆柱齿轮的设计44.1轴Ⅰ和轴Ⅱ上一对齿轮的设计···········································44.2轴Ⅱ和轴Ⅲ上一对齿轮的设计···········································74.3轴Ⅲ和轴Ⅳ上一对齿轮的设计·······································

4、····105轴的设计及轴承的校核135.1轴Ⅰ的设计计算·······················································135.2轴承的校核···························································186键的设计196.1键的选择·····························································196.2校核键连接的强度···········

5、··········································197联轴器的选择计算207.1轴Ⅲ端的联轴器选择计算···············································207.2轴Ⅳ的联轴器选择计算·················································208减速器箱体及其附件的设计218.1减速器附件的选择··············································

6、·······218.2选择适当型号·························································219润滑与密封219.1齿轮的润滑···························································219.2轴承润滑·····························································229.3减速器密封······················

7、·····································229.4密封方法的选取·······················································2210设计总结23参考文献······················································24..1设计任务1.1已知条件:数据编号:48输出力矩1:10N/m输出速度1:20r/min输出力矩2:200N/m输出速度2:50r/min1.2设计要求工作

8、条件:一班制,连续单向运转。载荷平稳,室工作,有粉尘(运输带与卷筒及支承间,包括)卷筒轴承的摩擦阻力影响已在F中考虑)。使用期限:十年,大修期三年。生产批量:10台。生产条件:中等规模机械厂,可加工7-8级精度齿轮及蜗轮。动力来源:电力,三相交流(220/380V)。运输带速度允许误差:±5%。1.3设计示意图:图任务设计示意图2电机选择2.1各传动效率的确定η—联轴器效率:η=0.99η—闭式圆柱齿轮传动效率:η=0.98η—一对滚动轴承

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。