TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf

TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf

ID:434441

大小:478.80 KB

页数:8页

时间:2017-08-01

TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf_第1页
TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf_第2页
TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf_第3页
TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf_第4页
TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf_第5页
资源描述:

《TBT3083-2003 高锰钢辙叉电弧焊补技术条件_.pdf》由会员上传分享,免费在线阅读,更多相关内容在行业资料-天天文库

1、ICS45.080S,夕1Y.?中华人民共和国铁道行业标准TB/T3083-2003高锰钢辙叉电弧焊补技术条件Specificationforarcweldingrepairofhighmanganesesteelcrossingwww.bzfxw.com2003-10-31发布2003-10-31实施中华少L民共和国铁道部发布TB/T3083-2003目次前言·.................................................................................

2、................................II1范围·..............................................................................................................12规范性引用文件························,················································⋯⋯,...⋯⋯,....⋯⋯13要求·..............

3、................................................................................................13.1焊条和焊丝·································,··································⋯⋯,·,....................⋯⋯13.2焊补设备························································

4、············································⋯⋯23.3焊补范围························································⋯⋯,,.,................⋯⋯,.⋯,.,二,..⋯⋯23.4焊补要求·································································⋯⋯,·...............⋯⋯,⋯,.,二,,二23.5焊后检查·······

5、··········································································⋯⋯,.............⋯⋯33.6焊补工艺卡··············································,···················································⋯⋯34试验方法·······································,·················

6、····························..................⋯⋯35焊条、焊丝和焊补设备检验规则······································································.⋯⋯,..⋯55.1出厂检验·······························,·····,··························.···································⋯⋯55.2型式检验·,···

7、····························································⋯⋯,.............····⋯⋯,⋯,⋯⋯5www.bzfxw.comTB/T3083-2003前言本标准参考了铁路合作组织(OSShDR7572)备忘录《线上及车间内高锰钢辙叉修复方法》和美国焊接协会(ANSI/AWSD15.2)标准《铁道用钢轨及相关产品焊接技术条件》中的有关内容。本标准由铁道部标准计量研究所提出并归口。本标准起草单位:铁道科学研究院金属及化学研究所、铁道部标准计量研究所、

8、广州康泰科技实业公司、广州铁路(集团)公司、重庆运达机电设备制造有限公司。本标准主要起草人:丁韦、黄辰奎、朱梅、谭亦东、翟成文、周源。本标准为首次发布。本标准委托铁道科学研究院金属及化学研究所负责解释。www.bzfxw.comTB/T3083-2003高锰钢辙叉电弧焊补技术条件,范围本标准规定了高锰钢

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。