JJF1015-2002-计量器具型式评价和型式批准通用.pdf

《JJF1015-2002-计量器具型式评价和型式批准通用.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国国家计量技术规范JJF1015-2002计量器具型式评价和型式批准通用规范GeneralNormforPatternEvaluationandPatternApprovalofMeasuringInstruments2002一05一16发布2002一08一01实施国家质量监督检验检疫总局发布JJF1015-2002屯计量器具型式评价和尹。.0.O.0.0.0.0.O.0.0.0.0.0.0.-，，型式批准通用规范JJF1015-2002，夕代替JJF1015-1990夕，GeneralNormforPatternEvaluatio

2、nand.o.o.o.}.o.o.o.o.o.o.o.o.o.o.‘PatternApprovalofMeasuringInstruments本技术规范经国家质量监督检验检疫总局于2002年05月16日批准，并自2002年08月01日起施行。归口单位:全国法制计量管理计量技术委员会起草单位:国家质量监督检验检疫总局计量司辽宁省质量技术监督局本规范由国家质量监督检验检疫总局计量司负责解释JJF1015-2002本规范主要起草人:王顺安(国家质量监督检验检疫总局计量司)张巨岩(辽宁省质量技术监督局)张文美(辽宁省计量科学研究院)张子剑(辽宁省计量科

3、学研究院)参加起草人:孙丽华(辽宁省计量科学研究院)汤东来(辽宁省计量科学研究院)JJF1015-2002目录1范围······················，··························································‘········⋯⋯(1)2引用文献，··，················，·，·····。·····························。····················，····⋯⋯(1)3术语···············‘····，·，··

4、···········，·，··，·········‘·····，·，························一(1)3.1计量器具·············，······································，····························一(1)3.2型式批准·················································································⋯⋯(1)3.3型式评价····················

5、·················································。···········⋯⋯(1)4办理型式批准的程序，，··，··，，，···········，··，··，!·················，·1·····甲······⋯⋯(1)4.1申请·............................................................................··········一(1)4.2型式评价······························

6、··················································。·一(2)4.3型式批准·················································································⋯⋯(2)5申请单位应提交的技术资料和试验样机·············································⋯⋯(2)5.1提交的技术资料·········，··················，···················

7、··········‘····，··，··，⋯⋯(2)5.2提供试验样机···························，·············································⋯⋯(2)6法制管理要求···············································································一(3)6.1计量单位要求·······，····················，····················，············

8、·············⋯⋯(3)6.2准确度(最大允许误差)要求‘··】··，·······，·····-，，，，···············，