J BT5000.13-1998-重型机械通用技术条件包装.pdf

《J BT5000.13-1998-重型机械通用技术条件包装.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS55.020J08Jjc?中华人民共和国机械行业标准JB/T5000.13一1998重型机械通用技术条件包装TheheavymechanicalgeneraltechniquesandstandardsPacking1998-09-30发布1998-12-01实施国家机械工业局发布JB/T5000.13-1998目次前言1范围................................................................................···········”············⋯⋯，.12引用标准···

2、······················“·············································，···························⋯⋯13包装型式与技术要求··························································································⋯⋯14框架木箱·............................................................................

3、.............................·一35包装标志·······················································。·······。··························，············⋯⋯36随机文件·.............................................................................................................47铁路运输对包装的要求··············

4、··································································....·.⋯⋯4附录A(标准的附录)限界图····················，··················。·····.···，····························⋯⋯5附录B(提示的附录)包装型式············································································..·.⋯⋯7附录C(提示的附录)产品的紧固方法·

5、··················，···········.··························..⋯⋯11JB/T5000.13-1998前言本标准的附录A是标准的附录，附录B和附录C是提示的附录。本标准由机械工业部冶金设备标准化技术委员会提出并归口。本标准起草单位:沈阳重型机械集团有限责任公司、沈阳矿山机器厂、西安重型机械研究所。本标准主要起草人:魏国君。中华人民共和国机械行业标准重型机械通用技术条件JB/T5000.13-1998包装、TheheavymechanicalgeneraltechniquesandstandardsPacki

6、ng1范围本标准规定了重型机械产品的包装型式、包装要求和包装设计等。本标准适用于重型机械产品的包装。凡图样及技术文件中无特殊要求时，均应符合本标准的规定。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB19。一9。危险货物包装标志GB191一9。包装储运图示标志GB1413一85集装箱外部尺寸和额定重量GB1834一8。通用集装箱最小内部尺寸GB4879一85防锈包装GB6388一86运输包装收发货标志GB7284一87框架太箱包装

7、型式与技术要求3.1箱装3.1.1普通箱3.1.2普通滑木箱3.1.3框架滑木箱3.1.3.1封闭箱3.1.3.2花格箱3.2局部包装3.3敞装3.4捆装3.5裸装3.6常见包装型式的结构示例及适用范围见附录B(提示的附录)3.7包装箱顶部型式一般为平顶，如不经海运且无堆码要求时也可采用非平顶3.8基本要求3.8.1产品包装应根据产品的特点及储运条件采用不同的包装型式和防护方法。3.8.2产品包装应符合科学、经济、牢固、美观、适销的要求。在正常储运条件下，应保证产品自制造厂包装之日起12个月内不至因包装不善而产生锈蚀、长霉、降低精度、残损或散失等现象。特殊情况按

8、供国家机械工业局1998