欢迎来到天天文库
浏览记录
ID:24552027
大小:54.50 KB
页数:4页
时间:2018-11-14
《快速ciscoios导入实践操作》由会员上传分享,免费在线阅读,更多相关内容在学术论文-天天文库。
1、快速ciscoios导入实践操作~教育资源库 第一步: 先打开超级终端,进入rommon模式(Ctrl+Break组合键),键入confreg,如下: rommon1>confreg回车 onfigurationSummary enabledare: loadromafterbootfails consolebaud:9600 boot:imagespecifiedbythebootsystemmandsordefaultto:cisco2-C2600 ****显示 doyouode?y
2、/n[n]:n(选择no) enableuseinIPbcastaddress?y/n[n]:n(选择no) disableloadromafterbootfailsy/n[n]:n(选择no) enableuseallzerobroadcast?y/n[n]:n(选择no) enablebreak/aborthaseffect?y/n[n]:n(选择no) enableignoresystemconfiginfo?y/n[n]:n(选择no) changeconsolebaudratey/n[n
3、]:y(选择yes) enterrate:0=9600,1=4800,2=1200,3=24004=19200,5=38400,6=57600,7=115200[0]:7(选择7,用最大的115200速率的xmodem传输) changethebootcharacteristics?y/n[n]:n(选择no) ConfigurationSummary enabledare: loadromafterbootfails consolebaud:115200 boot:imagespecifiedby
4、 thebootsystemmandsordefaultto:cisco2-C2600 doyouustresetorpomon2>reset回车 注意:在此时键入reset键,然后再修改超级终端里设置端,重新建立一个超级终端连接之前,开始定义串口速度(我的电脑速率为115200,记住,一定这么做,(期间系统重新启动)启动后,出--端口属性----串口速度调为115200,否则出现乱码! rommon1>xmodem-cr Donotstartthesendingprogramyet. i
5、nvokethisapplicationonlyfordisasterrecovery. Doyouodem协议,点击发送即可发送文件----选择IOS镜像文件所在地以及选择使用然后等待10-20分钟左右就把3-6M的IOS灌进去了 !!!!会自动引导IOS(c2600-i-mz.122-8.T10.bin),进入EN模式,shoz.122-8.T10.bin(delected)的标志,在EN模式下,用 squeezeflash:c2600-i-mz.122-8.T10.bin物理删除它。(#######¥
6、¥¥¥¥记住一定不要重起) 其实IOS没有倒入,是调用的配置文件。 shoz.122-8.T10.bin) en copytftpflash:c2600-i-mz.122-8.T10.bin 完毕后 shoz.122-8.T10.bin,后面没有delected 倒入成功 conft config-register0x2102 bootsystemflashc2600-i-mz.122-8.T10.bin exit exit wr reload 会引导到正常的操作模式下,成功 第三
7、步: 改到9612下一页友情提醒:,特别!00,可要可不要上一页12友情提醒:,特别!
此文档下载收益归作者所有