JB-T5000.13-1998 重型机械通用技术条件 包装

《JB-T5000.13-1998 重型机械通用技术条件 包装》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS55.020J08Jjc?中华人民共和国机械行业标准JB/T5000.13一1998重型机械通用技术条件包装TheheavymechanicalgeneraltechniquesandstandardsPacking1998-09-30发布1998-12-01实施国家机械工业局发布JB/T5000.13-1998目次前言1范围................................................................................···········”··········

2、··⋯⋯，.12引用标准·························“·············································，···························⋯⋯13包装型式与技术要求··························································································⋯⋯14框架木箱·..............................................

3、...........................................................·一35包装标志·······················································。·······。··························，············⋯⋯36随机文件·..........................................................................................

4、...................47铁路运输对包装的要求················································································....·.⋯⋯4附录A(标准的附录)限界图····················，··················。·····.···，····························⋯⋯5附录B(提示的附录)包装型式·········································

5、···································..·.⋯⋯7附录C(提示的附录)产品的紧固方法···················，···········.··························..⋯⋯11JB/T5000.13-1998前言本标准的附录A是标准的附录，附录B和附录C是提示的附录。本标准由机械工业部冶金设备标准化技术委员会提出并归口。本标准起草单位:沈阳重型机械集团有限责任公司、沈阳矿山机器厂、西安重型机械研究所。本标准主要起草人:魏国君。中华人民共和国机械行业标准重型机械通用

6、技术条件JB/T5000.13-1998包装、TheheavymechanicalgeneraltechniquesandstandardsPacking1范围本标准规定了重型机械产品的包装型式、包装要求和包装设计等。本标准适用于重型机械产品的包装。凡图样及技术文件中无特殊要求时，均应符合本标准的规定。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB19。一9。危险货物包装标志GB191一9。包装储运图

7、示标志GB1413一85集装箱外部尺寸和额定重量GB1834一8。通用集装箱最小内部尺寸GB4879一85防锈包装GB6388一86运输包装收发货标志GB7284一87框架太箱包装型式与技术要求3.1箱装3.1.1普通箱3.1.2普通滑木箱3.1.3框架滑木箱3.1.3.1封闭箱3.1.3.2花格箱3.2局部包装3.3敞装3.4捆装3.5裸装3.6常见包装型式的结构示例及适用范围见附录B(提示的附录)3.7包装箱顶部型式一般为平顶，如不经海运且无堆码要求时也可采用非平顶3.8基本要求3.8.1产品包装应根据产品的特点及储运条件采用不

8、同的包装型式和防护方法。3.8.2产品包装应符合科学、经济、牢固、美观、适销的要求。在正常储运条件下，应保证产品自制造厂包装之日起12个月内不至因包装不善而产生锈蚀、长霉、降低精度、残损或散失等现象。特殊情况按供国家机械工业局1998