骨架注塑模毕业设计(一模两腔带侧抽芯)

《骨架注塑模毕业设计(一模两腔带侧抽芯)》由会员上传分享，免费在线阅读，更多相关内容在学术论文-天天文库。

1、系别：专业：模具设计与制造姓名：学号：200900111025指导老师：老师2012年4月5前言光阴似梭，大学三年的学习一晃而过，为具体的检验这三年来的学习效果，综合检测理论在实际应用中的能力，除了平时的考试、实验测试外，更重要的是理论联系实际，让我们走向社会之前完成一次综合性设计。即本次设计的课题是骨架（SMBS-04）的注射模设计,是对以前所学课程的一个总结。本次毕业设计课题来源于生活，应用广泛，但成型难度大，模具结构较为复杂，对模具工作人员是一个很好的考验。它能加强对塑料模具成型原理的理解，同时锻炼对塑料成型模具

2、的设计和制造能力。在此次设计中，主要用到所学的注射模设计，以及机械设计等方面的知识。着重说明了一副注射模的一般流程，即注射成型的分析、注射机的选择及相关参数的校核、模具的结构设计、注射模具设计的有关计算、模具总体尺寸的确定与结构草图的绘制、模具结构总装图和零件工作图的绘制、全面审核投产制造等。其中模具结构的设计既是重点又是难点，主要包括成型位置的及分型面的选择，模具型腔数的确定及型腔的排列和流道布局和浇口位置的选择，模具工作零件的结构设计，推出机构的设计，拉料杆的形式选择，排气方式设计等。通过本次毕业设计，使我更加了解

3、模具设计的含义，以及懂得如何查阅相关资料和怎样解决在实际工作中遇到的实际问题，这为我以后从事模具职业打下了良好的基础。本次毕业设计得到了老师和同学的帮助，特别是林章辉老师和蒋红卫老师的悉心指导，在此表示感谢！由于实践经验的缺乏，且水平有限，时间仓促。设计过程中难免有错误和欠妥之处，恳请老师批评指正。2012年4月5目录前言绪论········································································1第一章设计任务书···········

4、············································4第二章塑件分析·························································5一、塑件工艺性······················································5二、塑件结构分析···················································6第三章塑料材料的成型特性与工艺参数

5、··································7第四章成型设备的选择··················································9一、初选注射机·····················································9二、型腔数量的确定················································105第一章浇注系统的设计和排溢系统的设计····

6、···························11一、塑料制件在模具中的位置·······································11二、浇注系统的设计···············································12三、排溢系统的设计················································14第二章成型零部件的设计与计算············

7、····························15一、成型零件的结构设计···········································15二、成型零件工作尺寸的计算·······································15三、模架的选取····················································18第三章脱模机构的设计············

8、······································19一、脱模力的计算··················································195一、推出机构的设计······································