JJG(交通)019-1999车轮动平衡机检定转子检定规程.pdf

《JJG(交通)019-1999车轮动平衡机检定转子检定规程.pdf》由会员上传分享，免费在线阅读，更多相关内容在应用文档-天天文库。

1、免费标准网(www.freebz.net)中华人民共和国交通部部门计量检定规程JJG(交通)019-1999车轮动平衡机检定转子WheelDynamicBalancer'sAlignerRotator1999一03一01发布1999一06一01实施中华人民共和国交通部发布免费标准网(www.freebz.net)无需注册即可下载免费标准网(www.freebz.net)JJG(交通)019-1999车轮动平衡机检定转子尹o.o.o.o.o.o.o.o.o.o.o.o.0.0.、}}检定规程{JJG(交通)019-1999}己9VerificationRegula

2、tionofWheel弓4、.o.o.o.o.o.o.o.o.o.o.o.o.o.o.aDynamicBalancer'sAlignerRotator本检定规程经中华人民共和国交通部于1999年03月01日批准，并自1999年06月01日起施行。归口单位:交通部科技教育司起草单位:国家汽车检测设备计量站交通部标准计量研究所本规程技术条文由起草单位负责解释标准分享网www.bzfxw.com免费下载免费标准网(www.freebz.net)无需注册即可下载免费标准网(www.freebz.net)MG(交通)019-1999本规程主要起草人:张宪(国家汽车检测设备

3、计量站)关春善(国家汽车检测设备计量站)谢平(国家汽车检测设备计量站)参加起草人:邱宁(中国测试技术研究院)安果平(国家汽车检测设备计量站)陈柏年(交通部标准计量研究所)免费标准网(www.freebz.net)无需注册即可下载免费标准网(www.freebz.net)JJG(交通)019-1999目录1概述··············。·····································。····。···········，····················⋯⋯(1)2技术要求·····························

4、·································。······················。·⋯(1)3检定条件··········。·········。···。····························································一(1)4检定项目及检定方法··················································。··················⋯⋯(2)5检定结果处理与检定周期·...............................

5、.....................................(3)附录A检定转子质量级别及几何尺寸················································⋯⋯(4)附录B检定转子试重规格与数量··························。。·······················。··⋯⋯(5)附录C车轮动平衡机检定转子角度位置检定记录表······················。·······⋯⋯(6)附录D车轮动平衡机检定转子不平衡量检定记录表··················。。···

6、·······⋯⋯(8)附录E对应于各平衡品质等级的最大许用不平衡量·····························。⋯⋯(9)附录F测量原理图······。··············································，··················⋯⋯(9)附录G检定证书背面格式·········。·····················································⋯⋯(10)标准分享网www.bzfxw.com免费下载免费标准网(www.freebz.net)无需注册即可下

7、载免费标准网(www.freebz.net)JJG(交通)019-1999车轮动平衡机检定转子检定规程本规程适用于新制造、使用中和修理后的车轮动平衡机用检定转子的检定。概述检定转子是用于对车轮动平衡机进行检定的专用计量标准器具，一般由钢制成，它具有两个校正平面，每个校正平面上零度基准应在同一角度方向上。检定转子质量级别及几何尺寸见附录A所示。其工作原理是:应用检定转子自身高品质的平衡精度，对车轮动平衡机的分离比、重复性、相位误差以及平衡精度等计量指标，通过在检定转子上加相应试重进行检定。2技术要求2.1外观转子应有清晰的铭牌、质量级别、出厂日期和出厂编号，应有相

8、位刻线，无明显损坏、锈迹