JJF1091-2001测量内尺寸千分尺校准规范.pdf

《JJF1091-2001测量内尺寸千分尺校准规范.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、免费标准下载网(www.freebz.net)中华人民共和国国家计量技术规范JJF1091-2002测量内尺寸千分尺校准规范CalibrationSpecificationforMicrometersforMeasuringInsideDimension2002一11一04发布2003一05一04实施国家质量监督检验检疫总局发布免费标准下载网(www.freebz.net)无需注册即可下载免费标准下载网(www.freebz.net)JJF1091-2002马尹。.O.0.0.口.0.O.0.O.O.伪0.0.0..。.测量内尺寸千分尺校准规范。}

2、JJF1091-2002.心。。}代替JJG378-1985。心CalibrationSpecificationfor.。}JJG23-1988.洲MicrometersforMeasuringInsideDimension本规范经国家质量监督检验检疫总局于2002年11月04日批准，并自2003年05月04日起施行。归口单位:全国几何量工程参量计量技术委员会主要起草单位:黑龙江省计量检定测试院参加起草单位:青海量具刃具有限责任公司本规范由归口单位负责解释免费标准下载网(www.freebz.net)无需注册即可下载免费标准下载网(www.free

3、bz.net)JJF1091-2002本规范主要起草人:张黎平(黑龙江省计量检定测试院)梁玉红(黑龙江省计量检定测试院)马钟焕(吉林省计量检定测试院)参加起草人:刘文滨(黑龙江省计量检定测试院)张洪玲(青海量具刃具有限责任公司)李旭辉(黑龙江省计量检定测试院)免费标准下载网(www.freebz.net)无需注册即可下载免费标准下载网(www.freebz.net)JJF1091-2002目录I范围············································································

4、·············⋯⋯(1)2引用文献··················································································⋯⋯(1)3概述··························································································⋯⋯(1)4计量特性···············，················································

5、····················⋯⋯(2)4.1测力·······················································································⋯⋯(2)4.2刻线宽度及宽度差························································-············⋯⋯(2)4.3微分筒锥面的端面棱边至固定套管刻线面的距离······························⋯⋯(2)4.4微分筒锥面的端面

6、与固定套管毫米刻线的相对位置···························⋯⋯(2)4.5测量面的表面粗糙度··································································⋯⋯(2)4.6测量爪测量面的圆弧半径及素线平行度··········································⋯⋯(2)4.7示值误差··········································································

7、·······⋯⋯(3)4.8校对用的环规直径偏差及直径变动量·············································⋯⋯(3)5校准条件······································。·············································⋯⋯(3)5.1环境条件·················································································⋯⋯(3)5.2测量标准器及

8、其他设备·························································