垫片冲裁模毕业论文

《垫片冲裁模毕业论文》由会员上传分享，免费在线阅读，更多相关内容在学术论文-天天文库。

1、目录§前言任务描述·····································1一.冲压件工艺性分··································2二.冲压工艺方案的确定······························2三.主要设计计算····································2（1）排养方式的确定以及计算·······························2（2）冲压力的计算·········································2（3）压力中心的确

2、定及相关计算·····························3（4）工作零件刃口尺寸计算·································3（5）卸料橡胶的设计·······································4四.模具总体设计····································4-13-（1）模具类型的选择·······································4（2）定位方式的选择·······································4（3

3、）卸料，出件方式的选择·································4（4）导向方式选择·········································5五.主要零部件设计··································5（1）主要零件的结构设计···································5a.落料凸模··············································5b.冲孔凸模·····································

4、·········5c.凹模·················································5（2）定位零件的设计·······································6（3）导料板的设计·········································6（4）卸料板部件设计·······································6（5）模架及其他零部件设计·································6六.-13-模具总装图···········

5、···························7七.冲压设备的选定··································7八.工作零件的加工工艺·····························7九.模具的装配·····································8十．设计小结·······································9附图装配图········································10（参考文献）···························

6、··································11冲裁模设计说明书冲裁模设计：-13-根据给定工件图设计冲裁模具。工件尺寸如图所示，料厚t=1,材料:紫铜;大批量.要求:1.完成模具总装图(3D电子文档);2.完成总装配图,图纸符合国家制图标准;3.绘制工程图,图纸符合国家制图标准.4.编写设计说明书.(A4纸打印)工件图工件名称：垫片工件简图：如图所示生产批量：大批量工件材料：紫铜材料厚度：1mm一.冲压件工艺性分析此工件只有冲孔和落料两个工序。材料为紫铜，具有良好的冲压性能，适合冲裁。工件结果简单，有2个直径10mm的孔；孔与孔，孔与边

7、缘之间的距离满足要求，工件的尺寸全部为自由公差，可看着IT14级，尺寸精度底，普通冲裁就能满足要求。-13-二.冲压工艺方案的确定该工件包括落料冲孔两个基本工序，可有以下三种工艺方案：方案一：先落料，后冲孔。采用单工序模生产。方案二：落料—冲孔复合冲压。采用复合模生产。方案三：冲孔—落料级进冲压。采用级进模生产。方案一模具结构简单，但需要两道工序两套模具，成本高而生产效率低，难以满足大批量生产要求。方案二只需一套模具，工作精度及生产效率都比较高，但制造难度大，并且冲压成品件留在模具上，清理模具上的物料影响冲压速度，操作不方便。方案三也只需要一副模具，生产效率高，

8、操作方便，设计简单，由于