jjg571-2004读数、测量显微镜检定规程

《jjg571-2004读数、测量显微镜检定规程》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国国家计量检定规程JJG571-2004读数、测量显微镜ReadingMicroscopeandMeasuringMicroscope2004一09一21发布2005一03一21实施国家质量监督检验检疫总局发布JJG571-2004产。.O.O.O.口.O.口.O.O.O.O.O.O.O.、己全读数、测量显微镜检定规程'>JJG571-2004己代替JJG904-1996VerificationRegulationofReading弓代替JJG571-1988MicroscopeandMeasuringMicroscope弓夕飞

2、.，.‘，.‘，.o.0.0.，“，.o.‘，.o.o.o.。。本规程经国家质量监督检验检疫总局于2004年09月21日批准，并自2005年03月21日起施行。归口单位:全国几何量工程参量计量技术委员会主要起草单位:中国计量科学研究院河南省计量测试研究所参加起草单位:中国航空工业第一集团公司第三O四研究所本规程委托全国儿何量工程参量计量技术委员会负责解释JdG571-2004本规程主要起草人:朱小平(中国计量科学研究院)张卫东(河南省计量测试研究所)张恒(中国计量科学研究院)参加起草人:赵新丽(中国航空工业第一集团公司第三0四研究所)王蔚晨

3、(中国计量科学研究院)JJG571-2004目录1范围·····································、···················································⋯⋯(1)2引用文献·················································································⋯⋯(1)3概述································，·························

4、·····························⋯⋯(1)4计量性能要求··············································································⋯⋯(2)4.1圆工作台受径向力时引起的位移··················································⋯⋯(2)4.2玻璃台面与纵、横向滑板移动方向的平行度····································⋯⋯(2)4.3纵、横向滑板移动的直线

5、度·······················································⋯⋯(2)4.4纵、横向滑板移动的相互垂直度··························，······················⋯⋯(2)4.5显微镜升降方向对玻璃台面的垂直度············································⋯⋯(2)4.6圆工作台的示值误差·····························································

6、····⋯⋯(2)4.7显微镜的示值误差···································································⋯⋯(2)4.8回程误差·······················································，·························⋯⋯(2)5通用技术要求··············································································⋯⋯(

7、3)5.1外观·······················································································⋯⋯(3)5.2各部分的相互作用··································································⋯⋯(3)5.3显微镜各刻线间的相对位置························································⋯⋯(3)5.4棱镜座转动引起影像的位移·

8、······················································⋯⋯(4)5.5螺旋线分划板中心与回转中心的重合性··········