JBT 7215-1994 锻焊结构热壁加氢反应器 技术条件.pdf

《JBT 7215-1994 锻焊结构热壁加氢反应器 技术条件.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、J8中华人民共和国机械行业标准JB/T7215一94锻焊结构热壁加氢反应器技术条件1994-07-18发布1995-07-01实施中华人民共和国机械工业部发布目次1主题内容与适用范围···，········，，·········。·，··········，······，······························‘·········⋯⋯(1)2引用标准·，········‘.............................................................·······，·

2、···“··········⋯⋯(1)3型号·.................................................................................................................(1)4有关术语的代号······················‘·····································································⋯⋯(2)5技术要求，················

3、····················，，，············，.·‘。······································，，····⋯⋯(2)6制造期间的检验规则··-，············‘·····。。。。·，··。···············，，······‘·························。。···，⋯(14)7标志、包装、运输·································，································.

4、...................8产品出厂文件·.....................................................................................................(17)附录A焊接材料技术条件(补充件)··························································，·········，⋯⋯(18)附录B加氢反应器缺陷的返修程序(补充件)········⋯⋯”············

5、········”···················⋯⋯(22)附录C加氢反应器((2%Cr-1Mo)焊接工艺评定项目(补充件)....................................·一(23)附录D焊缝射线检验(补充件)·，··”·······························“···································⋯⋯(25)标准分享网www.bzfxw.com免费下载中华人民共和国机械行业标准锻焊结构热壁加氢反应器JB/T7215一94技术条件1主题内容

6、与适用范围本标准规定了石油炼制用热壁加氢反应器(简称反应器)的制造技术要求、试验方法、检验规则及标志、包装、运输等内容。本标准适用于以2月Cr-1Mo钢为主体材料、锻焊结构的热壁加氢反应器。高于本标准及特殊的要求，应在图样或有关文件中规定。引用标准GB150钢制压力容器GB3077合金结构钢技术条件GB3323钢熔化焊对接接头射线照相和质量分级GB6394金属平均晶粒度测定方法GB10561钢中非金属夹杂物显微评定方法JB755压力容器锻件技术条件www.bzfxw.comJB2536压力容器油漆、包装、运输JB3963压力容

7、器锻件超声波探伤JB3965钢制压力容器磁粉探伤JB4708钢制压力容器焊接工艺评定3型号采用反应器的内径、最高工作压力等主要参数来命名反应器产品的型号。:，;反应器产品型号由以下五部分组成，即:容积，m3，符号M，数字从十位数取起最高工作温度，℃，符号T，数字从十位数取起最高工作压力，.MPa，取整数部分内直径(不计堆焊层)，mm壳体结构:DY-锻焊，有耐腐蚀堆焊层型号标记示例:堆焊不锈钢耐腐蚀层，锻焊结构，内直径3413mm，最高工作压力为”.65MPa，最高工作温度433'C，容积124m，的热壁加氢反应器.其型号表示为

8、DY3413一19T43M12,机械工业部1994-07-18批准1995-07-01实施1JBiT7215一944有关术语的代号PWHT最终焊后热处理RT射线照相检验ISR中间消除应力热处理CT化学成分分析DT尺寸检验VT外观检验MT磁粉探伤HB布氏硬度PT(液体)渗透探伤