QCT655-2005-摩托车和轻便摩托车制动器技术条件.pdf

《QCT655-2005-摩托车和轻便摩托车制动器技术条件.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华少味民共和国汽车行」k标准QC/T655-2005代替QC/T655-200摩托车和轻便摩托车制动器技术条件Specificationsofbrakesformotorcyclesandmopeds2005-07-26发布2006-01-01实施)写砚竺之碳和I定尊些4reJIA发布中华人民共和国国家发展和改革委员会月匕公口2005年第46号国家发展改革委批准《钢质管道单层熔结环氧粉末外涂层技术规范》等204项行业标准(标准编号、名称及实施日期见附件)，其中石油天然气行业标准87项、汽车行业标准9项

2、、黑色冶金行业标准55项、轻工行业标准43项、锅炉压力容器行业标准10项;批准《JB4732-1995钢制压力容器分析设计标准>)1项锅炉压力容器行业标准修改单，现予公布，《钢制压力容器分析设计标准》行业标准修改单自2005年10月1日起实施。附件:9项汽车行业标准编号、名称及实施日期中华人民共和国国家发展和改革委员会_:i00五年七月二十六日附件:9项汽车行业标准编号、名称及实施日期序号标准编号标准名称被代替标准编号实施日期88QC/T645-2005清障车QC/T645-20002006-01-01

3、89QC/T733-2005沙摸车辆2006-01-01摩托车和轻便摩托车发动机密封90QC/T734-20052006-01-01性能技术要求与试验方法摩托车和轻便摩托车方向把角度91QC/T735-20052006-01-01和宽度尺寸轿车发动机钢带组合油环技术条92QC/T736-20052006-01-01件93QC/T737-2005轿车发动机铸铁活塞环技术条件2006-01-01摩托车和轻便摩托车制动器台架94QC/T654-2005QC/T654-20002006-01-01试验方法摩托车

4、和轻便摩托车制动器技术95QC/T655-2005QC/T655-20002006-01-01条件96QC/T738-2005轻便摩托车用电喇叭技术条件2006-01-01QC/T655-2005目次前言···············································································································⋯⋯H1范围··································，

5、·········································································⋯⋯12规范性引用文件··，···。···，，·，·，。。，··。，···，···，···，，·，，·······，···，.⋯⋯，....⋯⋯，.，.，.⋯⋯，⋯⋯13分类······························································································

6、··············⋯⋯14要求···········································································································⋯⋯15检验规则······························································································........⋯⋯56标志、包装········

7、···························································································⋯⋯7附录A(规范性附录)制动性能要求·，·，，······························································⋯⋯8OUT655-2005前言本标准是对QC/T655-2000(摩托车和轻便摩托车制动器技术条件》的修订。本标准与QC/T655-2001〕相比，主要

8、有下列变化:—本标准覆盖了摩托车和轻便摩托车各种类型制动器的要求。—本标准增加了鼓式制动器技术条件。—本标准按制动器主要部件:制动主缸、制动钳和总成等分别制定技术要求和试验方法。—本标准规范了主要配套件:制动蹄、制动片、制动软管组合件、制动操纵杆、踏板、制动拉索和制动液等依据的标准。—本标准在附录中规定了制动器总成台架试验的内容和技术要求。本标准的附录A为规范性附录。本标准由全国汽车标准化技术委员会提出。本标准由全国汽车标准化技术委员会归口