jjf1125-2004滚刀检查仪校准规范

《jjf1125-2004滚刀检查仪校准规范》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国国家计量技术规范JJF1125-2004滚刀检查仪校准规范CalibrationSpecificationforGearHobTester2004一11一09发布2005一05一09实施国家质量监督检验检疫总局发布JJF1125-2004产.。滚刀检查仪校准规范.。.。JJF1125-2004.勺-勺CalibrationSpecification代替JJG65-1986一、forGearHobTester.0.o.o.口.0.0.o.o.o.o.o.o.0.口本规范经国家质量监督检验检疫总局于2004年11月09日批准，并自2005年05月09日起施行。归口单位:全

2、国几何量工程参量计量技术委员会起草单位:哈尔滨第一工具有限公司黑龙江省计量检定测试院哈尔滨市计量检定测试所吉林省计量科学研究院本规范由归口单位负责解释JJF1125-2004本规范起草人:孙醒凡(哈尔滨第一工具有限公司)李玉英(哈尔滨第一工具有限公司)王利(哈尔滨市计量检定测试所)马荃(黑龙江省计量检定测试院)马钟焕(吉林省计量科学研究院)工IF1125-2004目录1范围··························································································⋯wll了f“‘l⋯l门、飞︸飞

3、r、丫‘‘、了‘‘(了‘了lel‘(了tll‘f了‘ll了‘、l飞wl‘ll、lle2引用文献····················································································⋯⋯、，、、、，.才3概述··························································································⋯⋯4计量特性···。·················································

4、·············。·················⋯⋯4.1500mm标尺的示值误差···························⋯⋯“··⋯’‘”‘”‘’“““‘”“‘’‘”“‘4.2光学分度头的示值误差···························································⋯⋯“二、4.3指示、记录系统的示值误差···············································⋯、、、、才1、!、、，JJII、J⋯1“‘’““二、、1、，、，4.4传感器的测力·············

5、·····························································⋯⋯‘4.5切向拖架置零时刀口测刃与顶尖轴线的偏离····································⋯⋯4.6主拖架运动的直线度······························⋯⋯’““‘”“““”””‘””‘’“’‘’“’‘4.7轴向拖架运动的直线度··············································⋯⋯””‘’“““‘””4.8径向拖架运动的直线度···················

6、············································⋯⋯4.9四个筋形台工作面的表面粗糙度和平面度·······································⋯⋯4.10主拖架上两个筋形台工作面与主拖架运动方向的平行度·····················⋯⋯4.11正弦尺圆柱的表面粗糙度及其母线对筋形台面的平面度·····················⋯⋯4.12基圆盘母线与直尺工作面的平行度及其表面粗糙度···························⋯⋯4.13基圆盘和主轴的综合圆跳动·············

7、············································⋯⋯4.14上、下顶尖的径向圆跳动···························································⋯⋯4.巧直尺工作面与主拖架运动的平行度················································⋯⋯4.16啮合线导槽与轴向拖架导轨的平行度··························