29种机械安全技术操作规程

《29种机械安全技术操作规程》由会员上传分享，免费在线阅读，更多相关内容在应用文档-天天文库。

1、目 录一、土石方机械1、装载机安全技术操作规程·······························1二、动力机械1、发电机安全技术操作规程································22、锅炉安全技术操作规程·································3三、起重机械·1、起重安全操作规程·····································42、塔式起重机安全技术操作规程···························53、汽车起

2、重机安全技术操作规程···························64、龙门起重机安全技术操作规程···························75、叉车安全技术操作规程·································86、卷扬机安全技术操作规程······························9四、运输机械1、轨道车安全技术操作规程······························102、牵引车安全操作规程·······················

3、···········11五、砼及砂浆机械1、混凝土搅拌机安全技术操作规程·························122、混凝土搅拌站安全技术操作规程························133、砂浆搅拌机安全技术操作规程··························144、张拉安全操作规程···································15六、焊接机械1、电焊机安全技术操作规程······························162、气焊安全技术操

4、作规程································173、对焊机安全技术操作规程······························18七、加工机械1、车床安全技术操作规程·······························192、刨床安全技术操作规程·······························203、钻床安全技术操作规程·······························214、空气锤安全技术操作规程····················

5、··········225、钢筋切断机安全技术操作规程··························236、钢筋弯曲机安全技术操作规程··························24八、其他1、支拆模安全操作规程·································252、配电室安全技术操作规程······························263、现场施工用电安全技术操作规程·························274、手持电动工具安全技术操作规程····

6、·····················295、电动砂轮机安全技术操作规程···························30装载机安全技术操作规程（1）装载机行驶时，应收回铲斗，铲斗离地约400～500mm。在行驶过程中注意是否有路障或高压线等。除规定的驾驶人员外，不准搭乘其它人员。（2）装载机行驶时，避免突然换向行驶，铲斗带负荷升起行驶时，不准急转弯和急刹车。（3）装载机在公路上行驶时必须遵守交通规则，谨慎驾驶，下坡禁止空档溜放。（4）在倾斜坡地若发动机熄火，应把铲斗放在地上并制动，将各操作杆置

7、于中位，再启动发动机。（5）装载机应注意斗杆不应升太高。（6）对边坡、壕沟、凹坑卸料时，注意不要使铲斗过于伸出，以免倾覆。（7）不得在倾斜度超过规定的场地上工作，作业区内不得有障碍物及无关人员。（8）装载机转向架未锁闭时，严禁站在前后车架之间检修保养。（9）大臂升起后，在进行润滑和调整等工作前，必须装好安全销或采取其它措施支住大臂，以防大臂落下伤人。（10）作业后，应将装载机停放在安全场地，将铲斗平放地面，所有操作杆置于中位，并制动锁定。 发电机安全技术操作规程（1）启动前应检查燃油箱油量是否充足，各油管及

8、接头处无漏油现象；冷却系统水量是否充足、清洁、无渗漏，风扇皮带松紧是否合适。检查内燃机与发电机传动部分应连接可靠，输出线路的导线绝缘良好，各仪表齐全、有效。（2）启动后，应低速运转3～5分钟，待温度和机油压轮均正常后，方可开始作业。发电机在升速中应无异响，滑环及整流子上电刷接触良好，无跳动及冒火花现象。待运转稳定，频率、电压达到额定值后，方可向外供电。（3）运行中出现异响、异味、水温急剧上升及机油压力急剧下降等情