各种机器设备操作规程

《各种机器设备操作规程》由会员上传分享，免费在线阅读，更多相关内容在工程资料-天天文库。

1、Selection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPointselection.ParagraaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPoction.ParagraphFormS

2、election.ParagraphFormaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPointselection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPoction.ParagraphFormat

3、.LineSpacingLinesToPoints(2Selection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPointselection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPoction.ParagraphFormat.LineSpacingLinesTo

4、Points(2)Selection.ParagraphFaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaahF溜子司机操作规程1.开车前的检查与准备：1.1检查各部螺丝是否紧固，联轴器是否良好，防护罩是否齐全，润滑油是否足够。1.2检查刮板是否齐全，有无弯曲和歪斜，连接是否良好。1.3检查电缆是否悬挂整齐，开关是否正立平稳，电气

5、设备有无失爆现象。1.4经检查没有问题时，合上开关手把。1.5检查液压联轴器水是否装满,是否是易熔合金片。2.操作方法2.1听开车信号后，开车时应先点动（一开一停）一次，没有问题时才正式开车。2.2因负荷大起动困难时，最多起动次数不得起动3次，每次不得超过15秒，否则应停车处理，严禁重载起动。2.3正常情况下，停车前应将溜槽里的煤拉完，以免造成下次起动困难。无特殊情况不允许重载启动。3.运行注意事项：3.1.随时检查电动机，减速器的声音和温度是否正常，防止损坏电机。3.2随时观察刮板链的松紧情况，防止回空链拉回煤。3.3发现前台停

6、车或溜煤眼装满时，应及时停车。Selection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPointselection.ParagraaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPoction

7、.ParagraphFormSelection.ParagraphFormaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPointselection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.LineSpacingLinesToPoction.

8、ParagraphFormat.LineSpacingLinesToPoints(2Selection.ParagraphFormat.LineSpacingLinesToPoints(2)Selection.ParagraphFormat.Lin