飞利浦工厂调试与设置说明

《飞利浦工厂调试与设置说明》由会员上传分享，免费在线阅读，更多相关内容在应用文档-天天文库。

1、飞利浦工厂调试与设置说明InstructionsforDebuggingandSettingofPhilipsPlant一：手动亮暗平衡的测试/Manualtestonlight/darkbalance1、操作方法/OperationmethodA、按PROD键进入“B/WBALANCE”状态，此时将处于并显示第一个可调项“副亮度（SUB-BRIGBT）”，亮暗平衡调试的OSD显示为项部单行。PressthePRODkeytoenterthe“B/WBALANCE”condition.Atthistime,t

2、hefirstadjustableitem,the“SUB-BRIGHT”isdisplayedonthescreen.TheON-SCREENDISPLAY(OSD)ofthelight/darkdebugisinsinglerow.B、在此状态下按TV/AV键可显示软件内部白场/暗场，便于工厂进行亮暗平衡调试接P+/P-翻页选择要调试的项目。Inthisstate,presstheTV/AVkeytodisplaythewhite/darkfieldinthesoftware,whichfacilitie

3、sthedebuggingoflight/darkbalancebytheplant,then,presstheP+/Pkeytoselectitemstobedebugged.C、按VOL+或VOL-对选择到的项目进行增/减调整。PresstheVOL+/VOL-keytorealizeup/downadjustmentofthevolumeoftheselecteditems.D、重复B、C步骤，直至调到满意结果，然后按2次PROD键退出。RepeatStepBandCuntiltheresultisto

4、yoursatisfaction.ThenpressthePRODkeytwiceforexit.2、可调项目列表/ListforadjustableitemsOSD显示/OSDdisplay名称/Description出厂设置/Ex-factorysettingSUB-BRIGHT付亮度设置Sub-brightsetting15R-BIA红偏压Redbiasvoltage32G-BIA绿偏压Greenbiasvoltage32B-BIA蓝偏压Bluebiasvoltage32R-DRV红驱动Reddrive

5、r32G-DRV绿驱动Greendriver32B-DRV蓝驱动Bluedriver323、当用于维修时，可用一条亮线状态来大致调准暗平衡。当然处于“B/WBALANCB”状态时，按MUTB键，则可进入一条亮线状态；再次按MUTB键时，Whenitisusedformaintenance,we’dbetterusebright-linestatustoapproximatelyadjustthedarkbalance.Ofcourse,inthestateof“B/WBALANCE”,thescreenwil

6、lturnintoonebright-linestatusafterpressingtheMENUkey.PresstheMEMUkeyagain,A、则可由亮线状态返回到全屏状态。A.Thebright-linestatusreturnstothefullscreen.B、在此页调试下，按TV/AV键，屏幕会显示软件设计的内部亮或暗场信号，便于工厂进行亮/暗平衡的调试。B.Inthispage,presstheTV/AVkey,thenthescreenwilldisplaythesoftwareinter

7、nalbright/darkfieldsignalwhichisconvenientforthemanufacturertodebugthelight/darkbalance.二：调试项的调节及设置项的设置/Itemsadjustingandsetting1、操作方法：/OperationmethodA、按PROD键进入调试状态。A.PressthePRODkeytoenterthedebuggingstatus.OrB、用MENU键向上翻页或用CALL键向下翻页到要调整的项目所在的页面。B.Pressthe

8、MENUkeytopageuporpresstheCALLkeytopagedowntothepagewheretheitemsareadjusted.C、用P+/P-选择到要调整的项目。处于调试菜单的0:90显示时，可用0～9键直接快速选到对应当前页的0～9行。C.PresstheP+/P-keytoselecttheitemstobeadjusted.Ifthedebuggingmenuisdi