细牙螺纹底孔.pdf

《细牙螺纹底孔.pdf》由会员上传分享，免费在线阅读，更多相关内容在教育资源-天天文库。

1、A2.细牙系列(见表2)表2单位为毫米公称螺纹公差小径公差值公称螺纹公差小径公差值螺距螺距直径底孔等级上偏差下偏差直径底孔等级上偏差下偏差5H+0.05105H+0.13802.50.352.156H+0.071011.00.7510.206H+0.1780——07H+0.24205H+0.05105H+0.10703.00.352.656H+0.07108.01.07.006H+0.1530——07H+0.21705H+0.05105H+0.10703.50.353.156H+0.07109.01.08.006H+0.1530——07H+0.21705H+0.07105H

2、+0.10704.00.53.56H+0.099010.01.09.006H+0.15307H+0.13907H+0.21705H+0.07105H+0.10704.50.54.006H+0.099011.01.010.006H+0.15307H+0.13907H+0.21705H+0.07105H+0.10705.00.54.506H+0.099012.01.011.006H+0.15307H+0.13907H+0.21705H+0.07105H+0.10705.50.55.006H+0.099014.01.013.006H+0.15307H+0.13907H+0.217

3、05H+0.13805H+0.10706.00.755.206H+0.178015.01.014.006H+0.15307H+0.24207H+0.21705H+0.13805H+0.10707.00.756.206H+0.178016.01.015.006H+0.15307H+0.24207H+0.21705H+0.13805H+0.10708.00.757.206H+0.178017.01.016.006H+0.15307H+0.24207H+0.21705H+0.13805H+0.10709.00.758.206H+0.178018.01.017.006H+0.153

4、07H+0.24207H+0.21705H+0.13805H+0.107010.00.759.206H+0.178020.01.019.006H+0.15307H+0.24207H+0.2170专业文档供参考，如有帮助请下载。表2(续)单位为毫米公称螺纹公差小径公差值公称螺纹公差小径公差值螺距螺距直径底孔等级上偏差下偏差直径底孔等级上偏差下偏差5H+0.10705H+0.112022.01.021.006H+0.153016.01.5014.506H+0.17607H+0.21707H+0.25105H+0.10705H+0.112024.01.023.006H+0.153

5、017.01.5015.506H+0.17607H+0.21707H+0.25105H+0.10705H+0.112025.01.024.006H+0.153018.01.5016.506H+0.17607H+0.21707H+0.25105H+0.10705H+0.112027.01.026.006H+0.153020.01.5018.506H+0.17607H+0.21707H+0.25105H+0.10705H+0.112028.01.027.006H+0.153022.01.5020.506H+0.17607H+0.21707H+0.25105H+0.10705H+

6、0.112030.01.029.006H+0.153024.01.5022.506H+0.17607H+0.21707H+0.25105H+0.05905H+0.112010.01.258.806H+0.121025.01.5023.506H+0.17607H+0.18207H+0.25105H+0.05905H+0.112012.01.2510.806H+0.121026.01.5024.506H+0.17607H+0.18207H+0.25105H+0.05905H+0.112014.01.2512.806H+0.121027.01.5025.506H+0.17607H

7、+0.18207H+0.25105H+0.11205H+0.112012.01.5010.506H+0.176028.01.5026.506H+0.17607H+0.25107H+0.25105H+0.11205H+0.112014.01.5012.506H+0.176030.01.5028.506H+0.17607H+0.25107H+0.25105H+0.11205H+0.112015.01.5013.506H+0.176032.01.5030.506H+0.17607H+0.25107H+0.2510专业文档