QD桥式起重机制造工艺卡.doc

《QD桥式起重机制造工艺卡.doc》由会员上传分享，免费在线阅读，更多相关内容在工程资料-天天文库。

1、42页拱度测量修正表附表二41页主梁腹板下料预留拱度值（mm）附表一注：A为设计手册中值。B为大起现行工艺值。43页测量跨度时，拉力和自重下垂引起的修正值附表3注：测量的读数+修正值=实际长度单梁制作工艺流程框图（示意）▲▲▲▲★▲★★▲1、端梁制作有类似的工序过程（1-7）2桥机双梁制造工序工艺要求流程框图2、装配、制作工艺要求，技术标准，在制作工艺中详细述细3、工序号58部分，可以在前面先行制作与主梁同步，不浪费工时4、没有包括电器安装部分，一般电气安装在现场进行起QD桥机5～100吨系列吨位表起重机5101

2、6/3.220/532/550/1075/20100/20工作级别A5A6A5A6A5A6A5A6A5A6A5A6A5A6A5A6小车重量2.132.233.343.66.36.436.867.1810.911.715.516.427.728.332.432.7跨10.512.7513.014.314.7219.220.120.021.026.928.135.436.113.514.2514.5016.216.620.421.521.422.828.730.337.839.061.463.868.970.516.

3、516.116.418.919.423.423.723.625.232.233.5842.143.465.868.173.375.019.518.619.020.721.026.428.027.729.736.738.746.247.870.973.278.380.1重表2机吨位表L型单梁门机5～50吨系列吨位表表3度22.521.021.423.223.628.830.530.332.539.942.950.151.876.679.085.687.625.525.425.627.627.933.134.534.

4、736.845.047.155.657.781.583.980.292.428.528.528.731.031.336.438.038.440.649.350.659.661.888.190.997.499.831.531.431.634.434.739.541.441.544.352.855.364.967.394.196.7107.9112.051016/3.220/530/550/10起重量小车重量2.263.947.157.809.515.3跨度1827.538.147.750.662.085.0*223

5、0.542.750.854.864.590.0*2637.745.355.960.470.592.1*3044.252.462.572.885.094.83549.558.769.276.390.098.5*起LH葫芦双梁系列（5～32吨）位表跨起重量510/316/3.220/532/107.56.26.89.29.312.510.59.310.210.811.114.413.510.611.512.312.716.216.512.112.914.6914.918.6度19.513.715.016.817.22

6、1.322.516.517.219.219.723.7表4重机吨位表表5度15.5162.953.203.804.305.1016.5173.053.303.904.505.30LDA单梁葫芦（1～10吨）吨位表跨吨1235107.582.082.202.302.603.308.592.182.302.402.703.509.5102.252.402.502.803.7010.5112.352.502.602.904.0011.5122.452.652.803.404.2012.5132.602.802.903.

7、604.4013.5142.632.903.103.704.6014.5152.803.103.704.204.8519.53.404.254.705.005.7022.53.805.105.306.006.50MH单梁门式系列（箱型）跨度MH单主梁门机（花架）25162436423020304048跨度Q1091214171510141620181115192520121824312213.5202734Q9121518223251015205101520注：1以吨为单位，小数进位到百分位。2以数据如与图纸有误

8、差，以图纸为准。3其之相关系列，可比照相应系列的吨位进行参考。4划*号的为参照数（华东样版中无此数）。5LH系列为闭式空操重量，地操和开式的重量略少一些。6LDA系列，将点五级的都归到整数级，重量误差不超过50kg。7大吨位吊车、非标型具体重量根据图纸计算。8此表中重量可供销售部门、生产部门、装卸工组、管理人员使用。9此表中重量为公司专用，其它人使用出现问题概不负责。制表