水泥混凝土路面滑模施工工艺.doc

水泥混凝土路面滑模施工工艺.doc

ID:49051462

大小:156.00 KB

页数:34页

时间:2020-02-27

水泥混凝土路面滑模施工工艺.doc_第1页
水泥混凝土路面滑模施工工艺.doc_第2页
水泥混凝土路面滑模施工工艺.doc_第3页
水泥混凝土路面滑模施工工艺.doc_第4页
水泥混凝土路面滑模施工工艺.doc_第5页
资源描述:

《水泥混凝土路面滑模施工工艺.doc》由会员上传分享,免费在线阅读,更多相关内容在行业资料-天天文库

1、目录1工程概况···········································`42施工工艺介绍及施工工艺流程图表······················42.1原材料和配合比设计······························72.2施工准备······································122.3混凝土的拌合····································142.4混凝土的运输···································.152.5铺筑试验路段·

2、···································162.6DBI装置插入传力杆工艺························182.7拉杆的插入工艺··································192.8面板修整········································192.9微观构造制作———拖麻布······················192.切缝············································193提高水泥混凝土路面平整度的技术措施·····

3、···········204水泥混凝土路面滑膜施工质量控制·····················214.1原材料的质量控制·······························224.2施工过程质量控制·······························225施工中应注意的问题································255.1塌边问题·······································255.2麻面问题·······································255.3路面

4、混凝土密实度问题·····························255.4控制水泥混凝土路面塑性收缩裂缝···················256滑模施工安全保障措施·······························256.1一般规定·······································256.2施工现场·······································266.3滑模操作平台···································276.4动力及照明用电···········

5、······················286.5防雷防火·······································286.6施工操作·······································297环境保护及文明施工措施·····························307.1环保措施·······································307.2文明施工措施···································308工程施工总结·····················

6、··················319结束语·············································3110参考文献··········································32一.工程概况xxxx高速公路xxxxxx路段,某工程项目部承担了K14+830——K31+000的施工任务。业主要求主线采用水泥混凝土路面结构(面层采用28cm厚水泥混凝土;设计弯拉强度为5.0MPa),为此引进了一台美国EAST-POUR650全自动全液压滑膜机,全线采用滑膜摊铺机进行摊铺。二.施工工艺介绍传统施工混凝土路面

7、的过程是在基层上装好模板,用人工和辅助机具振捣,抹光,压纹,切缝。而滑模施工混凝土路面则是利用一套自动化程度很高的机械,自动完成路面的摊铺作业,是目前被广泛采用的先进施工技术。滑模式摊铺机的特点是不需轨模,采用由4个液压缸支撑腿控制的履带行走机构行走。整个摊铺机的机架支撑在四个液压缸上,它可以通过控制机械上下移动,调整摊铺层厚度。在摊铺机的两侧设置有随机移动的固定滑模板,因此不需加设轨模。这种摊铺机一次就可以完成摊铺,捣实,整平等多道工序。它的施工过程是在做好基层的路面两边拉2根钢丝绳作为新铺路面的中线、板厚、纵坡、横坡、弯道、超高等控制路面几何形状全部参数的引导

8、线,然后按

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。