JJG707-2003扭矩扳子检定规程.pdf

JJG707-2003扭矩扳子检定规程.pdf

ID:48072824

大小:541.90 KB

页数:18页

时间:2019-10-28

JJG707-2003扭矩扳子检定规程.pdf_第1页
JJG707-2003扭矩扳子检定规程.pdf_第2页
JJG707-2003扭矩扳子检定规程.pdf_第3页
JJG707-2003扭矩扳子检定规程.pdf_第4页
JJG707-2003扭矩扳子检定规程.pdf_第5页
JJG707-2003扭矩扳子检定规程.pdf_第6页
JJG707-2003扭矩扳子检定规程.pdf_第7页
JJG707-2003扭矩扳子检定规程.pdf_第8页
JJG707-2003扭矩扳子检定规程.pdf_第9页
JJG707-2003扭矩扳子检定规程.pdf_第10页
资源描述:

《JJG707-2003扭矩扳子检定规程.pdf》由会员上传分享,免费在线阅读,更多相关内容在行业资料-天天文库

1、中华人民共和国国家计量检定规程JJG707-2003扭矩扳子TorqueWrenches2003一09一23发布2004一03一23实施国家质量监督检验检疫总局发布JJG707-2003扭矩扳子检定规程、产0.0.O.O.O.O.O.O.O.口.O.O.口.O.。。。JJG707-2003.心。VerificationRegulation代替JJG707-1990心.护么.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,.‘,ofTorqueWrenches本检定规程经国家质量监督

2、检验检疫总局于2003年09月23日批准,并自2004年03月23日起施行。归口单位:全国力值、硬度计量技术委员会主要起草单位:上海704研究所国防扭矩计量专业站中国计量科学研究院参加起草单位:北京飞机维修工程有限公司山东日照东方计量有限公司本规程委托全国力值、硬度计量技术委员会负责解释JJG707-2003本规程主要起草人:商维绿(上海704研究所国防扭矩计量专业站)陈永培(上海704研究所国防扭矩计量专业站)李涛(上海704研究所国防扭矩计量专业站)张跃(中国计量科学研究院)于梅(中国计量科学研究院)参加

3、起草人:吴振雷(北京飞机维修工程有限公司)李苏时(北京飞机维修工程有限公司)窦宏良(山东日照东方计量有限公司)JJG707-2003目录1范围··························································································⋯⋯(1)2引用文献····················································································⋯⋯

4、(1)3概述··························································································⋯⋯(1)3.1用途·······················································································⋯⋯(1)3.2分类······················································

5、·································⋯⋯(1)4计量性能要求··············································································⋯⋯(1)4.1示值相对误差、示值重复性、示值分辨力·······································⋯⋯(1)4.2示值回零误差·······················································

6、····················⋯⋯(2)4.3超载性能················································································⋯⋯(2)5通用技术要求··············································································⋯⋯(2)5.1外观结构与附件········································

7、································⋯⋯(2)5.2操作适应性··············································································⋯⋯(2)5.3测量范围························································。························⋯⋯(2)6计量器具控制·····························

8、·················································⋯⋯(2)6.1检定条件·················································································⋯⋯(2)6.2检定项目和检定方法··········································

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。