JG-T168-2004建筑门窗内平开下悬五金系统.pdf

《JG-T168-2004建筑门窗内平开下悬五金系统.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS91.060.50O73J6中华人民共和国建筑工业行业标准JG/T168-2004建筑门窗内平开下悬五金系统Tilt&turnhardwaresystemofdoorsandwindows2004-12-02发布2005-03-01实施中华人民共和国建设部发布JG/T168-2004目次前言·············，············，·······················································，···············，···············

2、⋯⋯工1范围·················，··········，··················································································⋯⋯12规范性引用文件···········，···················································································⋯⋯13术语和定义·······························

3、······································································⋯⋯14分类和标记····································································································⋯⋯25要求················································，·············，···············

4、·····················，···········⋯⋯26试验方法············，········································，···················································一57检验规则······································································································⋯⋯88标志、包

5、装、运输及贮存·······························································，，················，·····⋯⋯9附录A(资料性附录)建筑门窗内平开下悬五金系统基本配置······································⋯⋯10附录B(规范性附录)模拟门窗及检测记录的要求···，······································，··········⋯⋯11JG/T168-2004月U言本标准

6、是参考CEN/TS13126-8《平开与平开下悬五金件质量要求、试验方法》进行编制的。本标准附录A为资料性附录、附录B为规范性附录。本标准由建设部标准定额研究所提出。本标准由建设部建筑制品与构配件产品标准化技术委员会归口。本标准起草单位:中国建筑金属结构协会建筑门窗配套件委员会、中国建筑标准设计研究院、济南格屋建筑五金有限公司、德国丝吉利娅一奥彼窗门五金(北京)有限公司、保定宝硕新型建筑材料有限公司、大连实德塑胶工业有限公司、深圳市立兴杨氏门窗配件有限公司、山东国强五金制品集团有限公司、北京诺托建筑材料有限公司、北新集团

7、建材股份有限公司五金事业部、上海东连工贸有限公司。本标准主要起草人:亘坯R、刘旭琼、房公殿、尚军、赵晓燕、程先胜、杨钟鹤、张海峰、河红、王莺燕、卢嘉志。JG/T168-2004建筑门窗内平开下悬五金系统范围本标准规定了建筑门窗内平开下悬五金系统(以下简称五金系统)的定义、分类、要求、试验方法、检验规则及标志、包装、运输、贮存。本标准适用于建筑门窗用内平开下悬五金系统。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准，然而

8、，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。GB/T700碳素结构钢GB/T702热轧圆钢和方钢尺寸、外形、重量及允许偏差GB/T905冷拉圆钢、方钢、六角钢尺寸、外形、重量及允许偏差GB/T2828.1计数抽样检验程序第1部分:按接收质量限(AQt