经纬仪使用说明.pdf

《经纬仪使用说明.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、保养总则1、避免震动前言长途运输仪器时，最好进行外包装或考虑防震措施，感谢您购买了BOIF电子经纬仪DJD2-PG系列，本仪器避免严重碰击仪器。2、安装和迁站是精密光电子测量仪器，维护和保养不善会使仪器精度降低，仪器在三角架上安装时，要一手扶住仪器照准部，一寿命缩短，甚至会影响正常测量工作。为了使您更好地使用本手旋转三角架中心螺旋，防止仪器滑落，卸下仪器时也应如此。如果需要与三角架一起搬运仪器时，切不可水平方仪器，请您仔细阅读本说明书并妥为保存备用。向扛在肩上，应保持直立位置搬运仪器。如果距离较远时，要取下仪器放在仪器箱内搬运。3、保持清洁仪器使用完毕后，要用绒布或毛

2、刷清除仪器表面灰尘，仪器被雨水淋后要及时擦干仪器。不可用化学擦拭剂擦洗电池盒及塑料部件，如需要，可用浸水软布擦洗上述部件。清洁外露光学件时，应用脱脂棉或镜头纸轻轻擦净，切不可用手帕、衣服擦拭光学零件表面。4、避免阳光长时间照晒仪器仪器不要放置在极热的地点，或被阳光长时间照晒，否则将影响仪器的测量精度。5、检查电池使用仪器前应检查电池电压，以保证仪器的正常使用。6、使用后须知仪器使用后应保存在干燥、通风良好的室内，室温应控制在45℃以下，仪器包装箱应经常更换干燥剂。12目录一．用途·············································

3、··5八．数据输出及串行通信································26二．仪器各部位名称····································61.RS—232C串行通信接口····························26三．显示器和显示标记·································82.数据输出···········································26四．操作面板和操作键·································9九．功能设置···

4、········································27五．测量前的准备·····································101.功能设置···········································271.安放仪器准备测量································102.功能设置操作方法······························282.开机···············································12十．垂直角零位校

5、正·································313.电压显示···········································13十一．其它功能··········································334.更换电池···········································141.用十字丝测距···································33六．角度测量···········································152.

6、倾斜改正功能···································341.水平角右旋增量和垂直角测量·······················153.照明和定时关机功能····························352.水平角右旋增量HR和左旋增量HL转换············16十二．检查和校正·····································363.水平角度设置·····································171.检查和校正长水准器························

7、·····364.重复角度测量·····································182.检查和校正圆水准器·····························375.垂直角百分比测量模式（坡度角测量）··············203.十字丝竖丝的检验和校正·························38七．距离坐标测量·····································214.仪器视准轴的检验和校正·························391.与测距仪（EDM）结合使用·····