模压产品公差

《模压产品公差》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、橡胶－制品公差模压制品公差标称尺寸M1级M2级M3级M4级以上以下F±C±F±C±F±C±F&C±04.06.310162540631001604.06.31016254063100160-0.080.100.100.150.200.200.250.350.400.3%0.100.120.150.200.200.250.250.400.500.4%0.100.150.200.200.250.350.400.500.700.5%0.150.200.200.250.350.400.500.700.800.8%0.250.300.400.500.600.801

2、.001.300.8%0.400.500.600.801.001.301.602.001.3%0.50.700.801.001.301.602.002.501.5%无支承挤压制品的截面尺寸公差标称尺寸等级E1±等级E2±等级E3±以上以下01.52.54.006.3010162540631.52.54.006.301016254063-0.150.200.250.350.400.500.700.801.001.300.250.350.400.500.700.801.001.301.602.000.400.500.700.801.001.301.602.0

3、02.503.20芯棒支承的挤压制品的截面尺寸公差单位：mm(另有规定除外)标称尺寸等级EN1±等级EN2±等级EN3±以上以下046.3101625406310046.310162540631001600.200.200.250.350.400.500.700.801.000.200.250.350.400.500.700.801.001.300.350.400.500.700.801.001.301.602.00160-0.6%0.8%1.2%表面光洁的挤压制品的外部尺寸公差单位：mm(另有规定除外)标称尺寸等级EG1±等级EG2±以上以下01016

4、2540631001601016254063100160-0.150.200.200.250.350.400.500.3%0.250.350.400.500.700.801.000.5%表面光洁的挤压制品的壁厚尺寸公差单位：mm(另有规定除外)标称尺寸等级EW1±等级EW2±以上以下046.3101646.31016250.100.150.200.200.250.200.200.250.350.40挤压制品的长度尺寸公差单位：mm(另有规定除外)标称尺寸等级EN1±等级EN2±等级EN3±以上以下04063100160250400630100016002

5、500400040631001602504006301000160025004000－0.70.81.01.31.62.02.53.24.05.06.30.16％1.01.31.62.02.53.24.05.06.310.012.50.32%1.62.02.53.24.05.06.310.012.516.020.00.5%挤压制品的切面尺寸公差单位：mm(另有规定除外)标称尺寸等级EN1±等级EN2±等级EN3±以上以下0.631.001.602.504.006.310161.001.602.504.006.301016250.100.100.150.2

6、00.200.250.350.400.150.200.200.250.350.400.500.700.200.250.350.400.500.700.801.00压延胶板的厚度误差标称厚度等级ST1±等级ST2±等级ST3±以上以下01.001.602.504.006.3010161.001.602.504.006.301016－0.150.150.20.250.350.40.53.5％0.20.250.350.40.50.70.85％0.250.350.40.50.70.81.07％压延胶板的宽度误差标称宽度等级SW1±等级SW2±等级SW3±以上以下

7、6301000160010001600－20302％25402.5％30503％