GBT5856-1999 热压机通用技术条件.pdf

《GBT5856-1999 热压机通用技术条件.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ics65.060.80B97中华人民共和国国家标准GB/T5856-1999热压机通用技术条件Generalspecificationofhotpress1999一01一25发布1999一08一01实施国家质董技术监督局发布GB/T5856-1999目次前言···········，····························································..............................................值1范

2、围···········································，，·····。·········。················。·，······························。⋯⋯12引用标准··············。，···················，，·。·······，············‘···，·················‘···············⋯⋯13热压机参数·........................

3、........................................·..........................·.⋯⋯14热压机柱塞系列·····························，··················......................................·一，..⋯⋯25热压机精度·......................................................................

4、.................................，二26技术要求··························································。············，，，·······························⋯⋯67试验方法····。····························································································

5、··········。⋯88检验规则·....................................·····，···，，···········‘······，··，，···········。··········，··，.⋯89标志、包装、运输、贮存·····，····‘···。···，········，·······1‘·。·········，···，··，·····，···“···，········，·一8Gs/T5856-1999前言本标准是根据日本工业标准JISB6548-198

6、6(热压机的试验及检验方法》对GB/T5856-1986(热压机精度》,GB/T5857-1986《热压机制造与验收技术条件》,GB/T1571-1988《多层热压机参数》进行修订的。修订后将三个标准合并，将热压机精度、工作精度改为三级，将其公差值表示方法改为数值表示，对主要零部件柱塞和柱塞缸的检验项目也作了较大改动，对参数进行了必要的删除，并补充了热压机柱塞系列。本标准自实施之日起，代替GB/T5856-1986,GB/T5857-1986和GB/T1571-19880本标准由原中华人民共和国林

7、业部提出。本标准由全国人造板机械标准化技术委员会归口。本标准起草单位:中国林业科学研究院木材工业研究所、沈阳重型机械厂。本标准主要起草人:欧阳琳、朴成汉、武保染、邱瑞秋。中华人民共和国国家标准GB/T5856-1999热压机通用技术条件代替GB/T5855^-5857-1986GB/T1571-1988Generalspecificationofhotpress范围本标准规定了热压机的参数、精度、技术要求、试验方法、检验规则等通用技术条件。本标准适用于生产胶合板、纤维板、刨花板、饰面板等的多层热压

8、机。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB/T1801-1979公差与配合GB/T1184-1996形状和位置公差未注公差值GB/T2828-1987逐批检查计数抽样程序及抽样表(适用于连续批的检查)GB/T5226.1-1996工业机械电气设备第一部分:通用技术条件GB/T7935-1987液压元件通用技术条件GB/T7932--1987气