51单片机流水灯 程序

《51单片机流水灯 程序》由会员上传分享，免费在线阅读，更多相关内容在应用文档-天天文库。

1、1.第一个发光管以间隔200ms闪烁。2.8个发光管由上至下间隔1s流动，其中每个管亮500ms,灭500ms。3.8个发光管来回流动，第个管亮100ms。4.用8个发光管演示出8位二进制数累加过程。5.8个发光管间隔200ms由上至下，再由下至上，再重复一次，然后全部熄灭再以300ms间隔全部闪烁5次。重复此过程。6.间隔300ms第一次一个管亮流动一次，第二次两个管亮流动，依次到8个管亮，然后重复整个过程。7.间隔300ms先奇数亮再偶数亮，循环三次；一个灯上下循环三次；两个分别从两边往中间流动三次

2、；再从中间往两边流动三次；8个全部闪烁3次；关闭发光管，程序停止。1#include#defineuintunsignedintsbitled1=P1^0;voiddelay();voidmain(){while(1){led1=0;delay();led1=1;delay();}}voiddelay(){uintx,y;for(x=200;x>0;x--)for(y=100;y>0;y--);}2#include#include#defineu

3、intunsignedint#defineucharunsignedcharsbitp1=P1^0;uchara;voiddelay();voidmain(){a=0xfe;P1=a;while(1){a=_crol_(a,1);delay();P1=a;delay();}}voiddelay(){uintb;for(b=55000;b>0;b--);}3#include#include#defineuintunsignedint#defineucharunsig

4、nedcharvoiddelay(){uintx,y;for(x=100;x>0;x--)for(y=110;y>0;y--);}voidmain(){uchara,i;while(1){a=0xfe;for(i=0;i<8;i++){P1=a;delay(100);a=_crol_(a,1);}a=0x7f;for(i=0;i<8;i++){P1=a;delay(100);a=_cror_(a,1);}}}4#include#include#defineuint

5、unsignedint#defineucharunsignedcharvoiddelay(uinta){uintx,y;for(x=a;x>0;x--)for(y=110;y>0;y--);}voidmain(){ucharb;while(1){b++;P1=~b;delay(200);}}5#include#include#defineuintunsignedint#defineucharunsignedcharvoidmain(){uchara,i,j;whi

6、le(1){for(j=0;j<2;j++){a=0xfe;for(i=0;i<8;i++){P1=a;delay(200);a=_crol_(a,1);}a=0x7f;for(i=0;i<8;i++){P1=a;delay(200);a=_cror_(a,1);}}P1=0xff;for(j=0;j<10;j++){delay(300);P1=~P1;}}}voiddelay(){uintx,y;for(x=200;x>0;x--)for(y=110;y>0;y--);}6#include

7、.h>#include#defineuintunsignedint#defineucharunsignedcharvoiddelay(){uintx,y;for(x=300;x>0;x--)for(y=110;y>0;y--);}voidmain(){uchara,i,j;while(1){a=0xfe;for(j=0;j<8;j++){for(i=0;i<8-j;i++){P1=a;delay(200);a=_crol_(a,1);}a=_crol_(a,j);P1=0xff;a

8、=a<<1;}}}7#include#include#defineuintunsignedint#defineucharunsignedcharvoiddelay(uintz){uintx,y;for(x=z;x>0;x--)for(y=110;y>0;y--);}voidmain(){uchara,i,j;for(j=0;j<3;j++){P1=0x55;delay(300);P1=0xaa;del