欢迎来到天天文库
浏览记录
ID:39348609
大小:36.50 KB
页数:3页
时间:2019-07-01
《5700系列堆叠配置》由会员上传分享,免费在线阅读,更多相关内容在行业资料-天天文库。
1、设备组建堆叠示例(通过业务口)组网需求在一个新建的企业网络中,要求接入设备具有充足的端口数目,并且希望网络结构简单,易于配置和管理。如图1所示,根据用户需求,SwitchA、SwitchB和SwitchC三台接入交换机采用环形堆叠组网,并通过跨设备Eth-Trunk连接上层设备SwitchD。其中,SwitchA、SwitchB和SwitchC的角色分别为主、备、从,堆叠ID分别为0、1、2,优先级分别为200、100、100。由于组成堆叠的成员交换机在逻辑上是一个整体,所以整个网络在扩展了端口数量的同时也方便了用户对网络的管理和维护。现网设备以S5700-LI交换机为例,S5700-LI交
2、换机支持通过业务口连接方式组建堆叠。图1堆叠组建后的组网配置思路采用如下的思路配置:通过业务口连接方式组建堆叠时,为了能够在堆叠的成员交换机之间转发数据报文,需要配置逻辑堆叠端口,并加入物理成员端口。为方便用户管理,配置成员交换机的堆叠ID和优先级。SwitchA、SwitchB、SwitchC下电。按照图1所示,使用SFP+堆叠电缆连接各物理成员端口后再上电。说明:本端设备逻辑堆叠端口stack-portn/1里的物理成员端口只能与对端设备逻辑堆叠端口stack-portn/2里的物理成员端口相连。为提高可靠性、增加上行链路带宽,配置跨设备Eth-Trunk。操作步骤配置逻辑堆叠端口并加入
3、物理成员端口#配置SwitchA的业务口GigabitEthernet0/0/27、GigabitEthernet0/0/28为物理成员端口,并加入到相应的逻辑堆叠端口。system-view[HUAWEI]sysnameSwitchA[SwitchA]interfacestack-port0/1[SwitchA-stack-port0/1]portinterfacegigabitethernet0/0/27enableWarning:Enablingstackportcauseconfigurationlossontheinterface,continue?[Y/N]:y
4、 Info:Thisoperationmaytakeafewseconds.Pleasewaitforamoment....... [SwitchA-stack-port0/1]quit[SwitchA]interfacestack-port0/2[SwitchA-stack-port0/2]portinterfacegigabitethernet0/0/28enableWarning:Enablingstackportcauseconfigurationlossontheinterface,continue?
5、[Y/N]:y Info:Thisoperationmaytakeafewseconds.Pleasewaitforamoment....... [SwitchA-stack-port0/2]quit#配置SwitchB的业务口GigabitEthernet0/0/27、GigabitEthernet0/0/28为物理成员端口,并加入到相应的逻辑堆叠端口。system-view[HUAWEI]sysnameSwitchB[SwitchB]interfacestack-port0/1[Switc
6、hB-stack-port0/1]portinterfacegigabitethernet0/0/27enableWarning:Enablingstackportcauseconfigurationlossontheinterface,continue?[Y/N]:y Info:Thisoperationmaytakeafewseconds.Pleasewaitforamoment....... [SwitchB-stack-port0/1]quit[SwitchB]interfacestack-port0
7、/2[SwitchB-stack-port0/2]portinterfacegigabitethernet0/0/28enableWarning:Enablingstackportcauseconfigurationlossontheinterface,continue?[Y/N]:y Info:Thisoperationma
此文档下载收益归作者所有