常用PP厚度计算

《常用PP厚度计算》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、文件名稱4.1.4.2.2.6常用PP膠片規格常用PP膠片規格　（廠牌：南亞）PP類型含膠量填膠前厚度PP類型含膠量填膠前厚度PP類型含膠量填膠前厚度1080RC62%2.97mil2116RC50%4.73mil7628RC43%7.73mil1080MRRC65%3.28mil2116MRRC54%5.15mil7628MRRC47%8.51mil1080HRRC68%3.65mil2116HRRC58%5.77mil7628HRRC50%9.18mil4.1.4.2.2.7常用壓合疊構(1)四層板成品板厚

2、0.8mm1.0mm1.2mm1.6mm外層銅厚HOZHOZHOZHOZPP膠片2116MR7628HR7628MR2116HRCore板厚度0.38mm1/1OZ0.38mm1/1OZ0.60mm1/1OZ1.20mm1/1OZPP膠片2116MR7628HR7628MR2116HR外層銅厚HOZHOZHOZHOZP:5東莞聯橋電子有限公司（2）六層板成品板厚0.8mm1.0mm1.2mm1.6mm外層銅厚HOZHOZHOZHOZPP膠片2116MR2116HR1080MR2116MRCore板厚度0.11m

3、m1/1OZ0.18mm1/1OZ0.38mm1/1OZ0.50mm1/1OZPP膠片2116MR2116HR1080MR2116MRCore板厚度0.11mm1/1OZ0.18mm1/1OZ0.38mm1/1OZ0.50mm1/1OZPP膠片2116MR2116HR1080MR2116MR外層銅厚HOZHOZHOZHOZ(3)八層板成品板厚1.0mm1.2mm1.6mm2.0mm外層銅厚HOZHOZHOZHOZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm1/1OZ0.13

4、mm1/1OZ0.26mm1/1OZ0.38mm1/1OZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm1/1OZ0.13mm1/1OZ0.26mm1/1OZ0.38mm1/1OZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm1/1OZ0.13mm1/1OZ0.26mm1/1OZ0.38mm1/1OZPP膠片1080HR2116HR2116HR2116HR外層銅厚HOZHOZHOZHOZP:6(4)十層板成品板厚1.2mm1.6mm2.0m

5、m2.2mm外層銅厚HOZHOZHOZHOZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm1/1OZ0.21mm1/1OZ0.26mm1/1OZ0.30mm1/1OZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm1/1OZ0.21mm1/1OZ0.26mm1/1OZ0.30mm1/1OZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm1/1OZ0.21mm1/1OZ0.26mm1/1OZ0.30mm1/1O

6、ZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm1/1OZ0.21mm1/1OZ0.26mm1/1OZ0.30mm1/1OZPP膠片1080HR1080HR2116MR2116MR外層銅厚HOZHOZHOZHOZ以上均為理論疊構，具體需依銅箔厚度&內層殘銅率選擇不同的PP&Core板制作4.1.4.2.2.8壓合疊構設計（1）、优先选用厚度较大的芯板（尺寸稳定性相对较好）（2）、优先选用成本低之pp(对于同种玻璃布型prepreg,树脂含量高低基本不影响价格)（3）、优先选用

7、结构对称（4）、介质层厚度>内层铜箔厚度×2（5）、1-2层或兩芯板间禁止单张使用低树脂含量prepreg（6）、对于有5张或以上的半固化片排在一起或介电层厚度大于25mil，中间prepreg用光板代替（7）、內層銅厚為2oz底铜且1-2層或兩芯板間绝缘层厚度<14mil时，禁止使用单张prepreg，最外层需用高树脂含量prepreg（8）、内层铜厚1oz的板，1-2層或兩芯板間使用1张prepreg时,该prepreg需选用高树脂含量（9）、内层铜厚≥3oz的板禁止用单张PP,一般不用7628，须使用多张

8、树脂含量高的prepreg，如106、1080、2116……（10）、对于含有无铜区大于3″×3″或1″×5″的多层板,芯板间一般不单张使用prepreg