leica相关软件应用(第一部分)

《leica相关软件应用(第一部分)》由会员上传分享，免费在线阅读，更多相关内容在学术论文-天天文库。

1、数字测图软件应用实验指导书数字测图软件应用实验数字测图软件应用实验指导书指导书本实习用GPS模拟器进行，实习前请先在电脑上安装“模拟器”说明：本指导书为从《数字测图》书中节选内容。本实习的目的：通过本次实习掌握工程项目从实施到结束需要用到的相关测绘软件。实习要求：通过本次实习达到熟练应用相关测绘软件。1数字测图软件应用实验指导书测绘工程学院2012年目录1.1GPSRTK碎部测图···································································

2、············································································11.1.1准备工作·····································································································································11.1.2碎部测图·····························

3、········································································································31.2GPSRTK放样··············································································································································

4、··········41.2.1准备工作·····································································································································41.2.2参考站和流动站的设置·························································································

5、····················51.2.3实施放样·····································································································································52数字测图软件应用实验指导书1.1GPSRTK碎部测图利用RTK法进行数据采集，在开始测量之前，首先要对仪器和控制软件进行正确的设置，然后才能测得符合要求的结果。下面以LeicaGPS12

6、00RTK为例说明具体的操作步骤。1.1.1准备工作碎部测量之前的准备工作主要分为三部分，第一部分是参考站配置集的建立，第二部分是流动站配置集的建立，第三部分是坐标系的建立。1．参考站配置集的建立①在主界面选择“3管理”，F1继续。②在弹出的管理界面中将光标调整到“5配置管理”，F1继续。图1-1选择已经建好的配置集图1-2配置集命名③将光标调整到已经建好的参考站配置集“RTKReference”，如图1-1所示，F1继续，或者F2新建一个配置集。④给定配置集名称，例如“Satel-REF”,如图1-2所示，F

7、1保存。⑤在向导模式界面，点击F1设置相关参数。图1-3参考站实时模式设置⑥在实时模式界面将实时模式设为“参考站”，实时数据设为“Leica”，端口设为“端口1”，设备设为“Satelline3AS”，如图1-3所示。⑦在天线和天线高界面，天线模式设为“ATX1230GG三脚架”。⑧记原始观测数据设为“从不”。⑨其它参数可以用默认值，设置完成后，F1保存，F1继续，回到主菜单，一个名字为Satel-REF的参考站配置集已经建立完毕2．流动站配置集的建立①在主界面选择“3管理”，F1继续。1数字测图软件应用实验指

8、导书②在弹出的管理界面中将光标调整到“5配置管理”，F1继续。③将光标调整到已经建好的流动站配置集“SmartRoverRTK”，F1继续，或者F2新建一个配置集。④给定配置集名称，例如“Satel-RTK”，F1保存。⑤在向导模式界面，点击F1设置相关参数。图1-4流动站实时模式设置⑥在实时模式界面将实时模式设为“流动站”，实时数据设为“Leica”，端口设为“Clip-on”，设备