SY-T5530-2005-石油钻机和修井机用水龙头.pdf

《SY-T5530-2005-石油钻机和修井机用水龙头.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、75.180.01E92备案号:1中华人民共和国石油天然气行业标准SY/T5530-2005代替SY/T5530-1992石油钻机和修井机用水龙头Swivelforpetroleumdrillingandworkoverrigs2005-07一26发布2005一11-01实施国家发展和改革委员会发布SY/T5530-2005目次前言················································································································。·。··⋯n‘胜范

2、围···············································································································⋯⋯12规范性引用文件·········.·····················································································⋯⋯1飞口术语和定义··························································。··

3、·········································⋯⋯14型号与基本参数················。···············································································⋯⋯25连接尺寸····································，····································································⋯⋯2技术要求·····················

4、····················································································⋯⋯4检验方法及检验规则·······························，·······················。····························.··.·.⋯⋯58标志、包装、运输和贮存·········。··········································································⋯⋯6参

5、考文献········································································。···························。······.··.⋯⋯7SY/T5530-2005前言本标准修订并代替SY/T5530-1992《石油钻机用水龙头》。本标准与SY/T5530-1992相比，主要差异如下:—标准名称改为《石油钻机和修井机用水龙头》;—将石油钻机和修井机用水龙头的级别由6级增加为12级;—产品型号的表示方法由两部分改为3部分，增加了变型序号;—取消了原标准基本参数中有关连接尺寸的内容

6、，增加了“连接尺寸”一章;—增加了出厂检验和型式检验的判定规则等内容。本标准由全国石油钻采设备和工具标准化技术委员会提出并归口。本标准起草单位:兰州兰石集团有限公司。本标准参加起草单位:南阳二机石油装备(集团)有限公司。本标准主要起草人:高琳、钮忻蔚、王平、尹玉刚。本标准所代替标准的历次版本发布情况为:—SY/T5530-1992,SY/T5530-2005石油钻机和修井机用水龙头范围本标准规定了石油钻机和修井机用水龙头(以下简称水龙头)的型号与基本参数、连接尺寸、技术要求、试验方法及检验规则、标志、包装、运输和贮存。本标准适用于石油、天然气钻井和修井作业用水龙头的设计、

7、制造和检验。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。GB/T5677铸钢件射线照相及底片等级分类方法GB7233铸钢件超声探伤及质量评级方法GB/T9253.1石油钻杆接头螺纹GB/T9253.2石油天然气工业套管、油管和管线管螺纹的加工、测量和检验GB/T9443铸钢件渗透探伤及缺陷显示痕迹的评级方