JJF1084-2002-框式水平仪和条式水平仪校准.pdf

《JJF1084-2002-框式水平仪和条式水平仪校准.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国国家计量技术规范JJF1084-2002框式水平仪和条式水平仪校准规范CalibrationSpecificationforFrameLevelsandShaftLevels2002一05一24发布2002一08一24实施国家质量监督检验检疫总局发布JJF1084-2002框式水平仪和条式水平仪、广0.0.0.0.0.O.O.O.O.O.O.O.O.O..‘.。.。校准规范}JJF1084-2002.心.令.。{代替JJG38-1984.CalibrationSpecification

2、for今.心洲.叭.‘，.‘，.司，.‘》.‘，.‘，.‘，.‘，.‘，.记，.‘，.‘，.‘，.‘，FrameLevelsandShaftLevels本规范经国家质量监督检验检疫总局于2002年05月24日批准，并自2002年08月24日起施行。归口单位:全国几何量角度计量技术委员会起草单位:湖北省计量测试技术研究院本规范由归口单位负责解释J.TF1084-2002本规范主要起草人:汪丰焰(湖北省计量测试技术研究院)阎志京(湖北省计量测试技术研究院)郑华(湖北省计量测试技术研究院)参加起草人:黄润

3、华(湖北省计量测试技术研究院)杨莉(湖北省计量测试技术研究院)JJF1084-2002目录1范围··························································································⋯⋯(1)2引用文献····················································································⋯⋯(1)3概述············

4、·············································································⋯⋯(1)4计量特州·，···············································································⋯⋯(2)4.1工作面的平面度····。································································

5、⋯⋯‘”(2)4.2偏斜误差················································································⋯⋯(2)4.3零位误差·················································································⋯⋯(2)4.4分度值误差····················································

6、··························⋯⋯(2)5校准条件··········································，·········································⋯⋯(3)1环境条件·········⋯⋯(3)2测量标准及其他设备(3)6校准项目和校准方法(3)校准项目(3)6.2校准方法(3)7校准结果的表达················································⋯⋯“““““””

7、”‘”‘’‘’“’‘(6)8复校时间间隔······················································⋯⋯‘’““‘········⋯⋯“‘(6)附录A水平仪分度值计算实例(7)附录B水平仪零位检定器校准方法(10)附录C校准证书格式及内容(13)JJF1084-2002框式水平仪和条式水平仪校准规范范围本规范适用于分度值为(0.02-0.10)mm/m的框式水平仪和条式水平仪的校准。2引用文献本规范引用下列文献:GB/T16455-1996条式和框式水

8、平仪JJF1001-1998通用计量术语及定义JJF1059-1999测量不确定度评定与表示使用本规范时，应注意使用上述引用文献的现行有效版本。3概述框式、条式水平仪是利用液面水平的原理，以水准泡直接显示角位移，测量相对于水平和铅垂位置微小倾斜角度的一种通用角度计量器具;也可用于测量各种机床导轨的直线度、平面度及平行度，校正设备安装的水平和铅直位置等。框式水平仪和条式水平仪的外形结构如图1、图2所示。主体绝热手柄副水准泡主水准泡调整机构盖板副水准泡主水准泡调整机构盖板