利用vrrp实现路由器之间的分流及备份!(h3c)

《利用vrrp实现路由器之间的分流及备份!(h3c)》由会员上传分享，免费在线阅读，更多相关内容在学术论文-天天文库。

1、1.作业要求：利用vrrp实现路由器之间的备份实现两个路由器之间流量的分流（提高效率）利用通道技术来提高安全性2.拓扑图3.设备描述：路由器：H3CQuidwayR2621（R9R6）交换机：H3CQuidwayS2000(二层交换机S2)H3CQuidwayS3526E(三层交换机S1)4.设备配置4.1基本配置：路由器R9：[Router]sysnameR9[R9]inte1.10[R9-Ethernet1.10]vlan-typedot1qvid10//打标签[R9-Ethernet1.10]ip

2、add192.168.10.1255.255.255.0//配ip//这两步顺序不能颠倒！[R9-Ethernet1.10]inte1.20[R9-Ethernet1.20]vlan-typedot1qvid20[R9-Ethernet1.20]ipadd192.168.20.124路由器R6:[R6]inte1.10[R6-Ethernet1.10]vlan-typedot1qvid10[R6-Ethernet1.10]ipadd192.168.10.224[R6-Ethernet1.10]inte1

3、.20[R6-Ethernet1.20]vlan-typedot1qvid20[R6-Ethernet1.20]ipadd192.168.20.224交换机s1：[Quidway]sysnames1[s1]inte0/24[s1-Ethernet0/24]portlink-typetrunk//干道链路[s1-Ethernet0/24]porttrunkpermitvlanall//默认只允许vlan1通过，所以这里Pleasewait..................................

4、.........Done.[s1-Ethernet0/24]vlan10[s1-vlan10]porte0/3toe0/5//划分端口[s1-vlan10]vlan20[s1-vlan20]porte0/10toe0/15[s1]inte0/1[s1-Ethernet0/1]portlink-typetrunk[s1-Ethernet0/1]porttrunkpermitvlanall[s1-Ethernet0/1]disinte0/1Ethernet0/1currentstate:UPIPSendi

5、ngFrames'FormatisPKTFMT_ETHNT_2,Hardwareaddressis00e0-fc0e-b624TheMaximumTransmitUnitis1500Mediatypeistwistedpair,loopbacknotsetPorthardwaretypeis100_BASE_TX100Mbps-speedmode,full-duplexmodeLinkspeedtypeisautonegotiation,linkduplextypeisautonegotiationFl

6、ow-controlisnotenabledPort-flow-constrainhasnotbeenconfiguredcompletelyTheMaximumFrameLengthis1536BroadcastMAX-ratio:100%PVID:1Mditype:autoPortlink-type:trunkVLANpassing:1(defaultvlan),10,20VLANallowed:1(defaultvlan),2-4094Trunkportencapsulation:IEEE802.

7、1q交换机s2：[s2]inte1/0/24[s2-Ethernet1/0/24]portlink-typetrunk[s2-Ethernet1/0/24]porttrunkpermitvlanallPleasewait...........................................Done.[s2-Ethernet1/0/24]vlan10[s2-vlan10]porte1/0/3toe1/0/5[s2-vlan10]vlan20[s2-vlan20]porte1/0/10toe

8、1/0/15[s2]inte1/0/1[s2-Ethernet1/0/1]portlink-typetrunk[s2-Ethernet1/0/1]porttrunkpermitvlanallPleasewait...........................................Done.[s2-Ethernet1/0/1]disinte1/0/1Ethernet1/0/1currentstate:UPIPSendingFr