YZT0079-2002邮政用封装机测试规范.pdf

《YZT0079-2002邮政用封装机测试规范.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS03.240M80备塞昙·10543-2002YZ中华人民共和国邮政行业标准YZ/T0079-2002邮政用封装机测试规范Testproceduresforpostalinserter2002-07-04发布2002-08-01实施国家邮政局发布YZ/T0079-2002目次前言·..........................................................................................................................I1范围············

2、······································································································⋯⋯12规范性引用文件····································································································.⋯⋯13定义······························································

3、·····························，························⋯⋯14分类·················································································································⋯⋯15主要技术要求································································································⋯⋯1

4、6测试方法·····················，···，·················································································⋯⋯3YZ/T0079-2002前言本标准规定了邮政用封装机的定义、主要技术要求和测试方法，是参照目前国内使用封装机的技术性能而制定的。本标准由国家邮政局邮政科学研究规划院提出并归口。本标准起草单位:国家邮政局上海研究所本标准主要起草人:杨祖德陈卫民施咸祖YZ/T0079-2002邮政用封装机测试规范范围本标准规定了邮政用封装机的定义、主

5、要技术要求和测试方法。本标准适用于邮政用封装机的选用和检验。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。GB/T1416信封YD/T737-95信函封装技术要求YD/T738-95透明窗口信封YD/T844-19%信函设备噪声测量方法YZ/T0010-2000信函分拣设备电磁兼容性—静电放电和电快速瞬变脉冲群抗扰度要求3定义本标准采用下

6、列定义。3.1封装机inserter将账单、广告等内件装人标准信封的自动封装处理设备。3.2生产效率insertingeficiency封装机处理封装件与完成合格封装件的比率。4分类按使用场合分:办公型—单位时间内封装量较小，间断封装的封装机。生产型—单位时间内封装量较大，连续封装的封装机。按运行速度分:低速封装机:生产速度<3000封/h中速封装机:生产速度3000封/h--6000封/h高速封装机:生产速度>6000封/h5主要技术要求5.，环境适应性5.1.1气候环境适应性气候环境适应性见表toYZ/T0079-2002表1气候环境试验条件温度一50C

7、-40'C相对湿度30%-90%(无凝露)5.1.2电磁兼容性5.1.2.，静电放电干扰的试验要求应符合YZ/T0010-2000中4.1的规定。5.1.2.2电快速瞬变脉冲群的试验要求应符合YZ/T0010-2000中4.2的规定。5.2适应封装机的信封和内件5.2.1封装信封a)采用横式上开口。b)应符合GB/T1416中4,5.2,5.3的规定和YD/T738-95中4,5.1,5.2,5.3,6的规定。c)规格为GB/T1416中1号-7号、9号和YD/T738-95中5号、7号。d)封舌背胶应均匀，上胶后不应翘曲。信封平整度应<6.4mma5.2.

8、2封装内件a)内件纸张定量〕70g/mzob)内件规