通信机房蓄电池组通用技术规范

通信机房蓄电池组通用技术规范

ID:16058128

大小:22.69 KB

页数:13页

时间:2018-08-07

通信机房蓄电池组通用技术规范_第1页
通信机房蓄电池组通用技术规范_第2页
通信机房蓄电池组通用技术规范_第3页
通信机房蓄电池组通用技术规范_第4页
通信机房蓄电池组通用技术规范_第5页
资源描述:

《通信机房蓄电池组通用技术规范》由会员上传分享,免费在线阅读,更多相关内容在教育资源-天天文库

1、通信机房蓄电池组通用技术规范蓄电池组通用技术规范(2011年版)国家电网公司物资采购标准(二次设备卷电源系统册)蓄电池组通用技术规范(编号:1109007-0000-00)国家电网公司二〇一一年五月本次采购物资表蓄电池组通用技术规范通信蓄电池组采购标准技术规范使用说明1.本标准技术规范分为通用部分、专用部分。2.项目单位根据需求选择所需设备的技术规范。技术规范通用部分条款、专用部分标准技术参数表和使用条件表固化的参数原则上不能更改。3.项目单位应按实际要求填写项目需求部分。如确实需要改动以下部分,项目单位应填写专用部分项目单位技术差异表,并加盖

2、该网、省公司物资部(招投标管理中心)公章,与辅助说明文件随招标计划一起提交至招标文件审查会:1)改动通用部分条款及专用部分固化的参数。2)项目单位要求值超出标准技术参数值范围。3)根据实际使用条件,需要变更海拔高度、耐受地震能力、环境温度等要求。经招标文件审查会同意后,对专用部分的修改形成项目单位技术差异表,放入专用部分中,随招标文件同时发出并视为有效,否则将视为无差异。4.投标人逐项响应技术规范专用部分中标准技术参数表、项目需求部分和投标人响应部分三部分相应内容。填写投标人响应部分,应严格按招标文件技术规范专用部分的“招标人要求值”一栏填写相

3、应的投标人响应部分的表格。投标人还应对项目需求部分的项目单位技术差异表中给出的参数进行响应。项目单位技术差异表与标准技术参数表和使用条件表中参数不同时,以项目单位技术差异表给出的参数为准。投标人填写标准技术参数表时,如有偏差除填写投标人技术偏差表外,必要时应提供证明参数优于招标人要求的相关试验报告。5.对扩建工程,项目单位应在专用部分提出与原工程相适应的一次、二次及土建的接口要求。6.技术规范范本的页面、标题等均为统一格式,不得随意更改。目次通信蓄电池采购标准技术规范使用说明···································

4、····································································31总则···························································································································································52技术要求··········································

5、·········································································································52.1引用标准···············································································································································52.2通用要求···········

6、····································································································································62.3其他要求·······································································································································

7、········93试验·························································································································································104技术服务、设计联络、工厂检验和监造、工厂(现场)验收·····························································104.1技术服务···········

8、···········································································

当前文档最多预览五页,下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页,下载文档查看全文
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。