TBT3101-2005机车车辆用卡套式管接头技术条件.pdf

《TBT3101-2005机车车辆用卡套式管接头技术条件.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、rcs45.060.01S34TB中华人民共和国铁道行业标准TB/T3101-2005机车车辆用卡套式管接头技术条件Specificationofbayonetringcouplingsforrollingstock2005-03-29发布2005-07-01实施中华少味民共和国铁道部发布TB/T3101-2005目次前言·································································································

2、········⋯⋯n1.范围·····················，·······································，·········································⋯⋯1勺‘规范性引用文件·····································································，··························⋯⋯1︵‘︶技术要求·······················

3、·················································································⋯⋯14检验规则5质量保证·······。·。·。·。。·················。。················。·。················。···。·····················。·········⋯⋯3装6包·。···················。···。··············。···。·········

4、······。······················。·。···················。·。。一3附录A(规范性附录)组装要求········································································⋯⋯““·⋯’4TB/T3101-2005前言本标准的附录A为规范性附录。本标准由铁道行业内燃机车标准化技术委员会提出并归口。本标准主要起草单位:中国北车集团大同电力机车有限责任公司、中国南车集团株洲电力机车厂、中国北车集团大连机车

5、研究所。本标准主要起草人:张惠山、刘维民、赵风兰、张同铃、架丽华等。本标准为首次发布。TB/T3101-2005机车车辆用卡套式管接头技术条件，范围本标准规定了机车车辆用卡套式管接头(以下简称管接头)的技术要求及检验规则。本标准适用于机车车辆空气管路系统公称压力P,成1000kPa，工作温度一50℃一150℃的各种卡套式管接头及其零件。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准，然而，鼓励根据本标准达成协

6、议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。GB/T196-2003普通螺纹基本尺寸(ISO724:1993,ISOgeneralpurposemetricscrewthreads-Basicdimensions,MOD)GB/T197-2003普通螺纹公差(ISO965-1:1998,ISOgeneralpurposemetricscrewthreads-Tolerances-Partl:Principlesandbasicdata,MOD)GB/T699优质碳素结

7、构钢GB/T1184-19%形状和位置公差未注公差值(eqvISO2768-2:1989)GB/T1220不锈钢棒GB/T1804-2000一般公差未注公差的线性和角度尺寸的公差GB/T2828.1-2003/ISO2859-1:1999计数抽样检验程序第1部分:接收质量限(AQL)检索的逐批检验抽样计划(ISO2859-1:1999,IDT)GB/T3103.1-2002紧固件公差螺栓、螺钉和螺母(eqvISO4759-1.2000)GB/T6414-1999铸件尺寸公差与机械加工余量(eqvISO8062:1

8、994)GB/T7306.1-200055.密封管螺纹第1部分:圆柱内螺纹与圆锥外螺纹(eqvISO7-1:1994)GB/T7306.2-200055。密封管螺纹第2部分:圆锥内螺纹与圆锥外螺纹(eqvISO7-1:1994)GB/T7307-200155，非螺纹密封的管螺纹(eqvISO228-1:1994)GB/T11352-1989一般I程用铸造碳钢件(eqvIS