QCT699-2004车用起重尾板.pdf

《QCT699-2004车用起重尾板.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华人民共和国汽车行」至标准QC/T699-2004车用起重尾板Tail-liftforvehicle2004-02-10发布2004-08-01实施习之2月醚和lo_交J有攀导改鉴r发布QC/T699-2004目次前言···············································································································⋯⋯11范围···········································

2、·································································⋯⋯1z规范性引用文件···············································⋯⋯，’············.·......................⋯⋯13术语和定义··································································································

3、·⋯⋯14型号、基本参数·····························································································⋯⋯35要求················································，··························································⋯⋯36试验方法············································

4、·····································、····················⋯⋯57检验规则····································································································..⋯⋯78标志、使用说明书·····························································........................⋯⋯89包

5、装、运输和贮存·····································································.··..............⋯⋯8附录A(资料性附录)产品型号的编制示例····························································⋯⋯9QC/T699-2004前言本标准的附录A是资料性附录。本标准由中国汽车工业协会提出。本标准由全国汽车标准化技术委员会归口。本标准起草单位:深圳市凯卓立液压设备有限公司、国营安中机械厂

6、。本标准主要起草人:刘崇义、吴先谋、梁上愚、王泽黎、高文利。OUT699-2004车用起重尾板范围本标准规定了车用起重尾板的术语和定义、型号、基本参数、要求、试验方法、检验规则、标志、说明书、包装、运输和贮存。本标准适用于安装在车辆尾部的液压式车用起重尾板(简称尾板)。2规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准。然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。

7、GB/T3766液压系统通用技术条件GB4785汽车及挂车外部照明和信号装置的安装规定GB/T6739涂膜硬度铅笔测定法GB/T7935-1987液压元件通用技术条件GB/T9286色漆和清漆漆膜的划格试验GB/T9969.1工业产品使用说明书总则JB/T5943工程机械焊接件通用技术条件JB/T6996-1993重型机械液压系统通用技术条件JB/T8727液压软管总成QC/T252专用汽车定型试验规程QC/T29104专用汽车液压系统液压油固体污染度限值QC/T29105.1一29105.4专用汽车液压系统液压油固体污染度测试方法3

8、术语和定义下列术语和定义适用于本标准。最大起重质iMmaxcarringcapacity载荷质心位于图1所示位置时，尾板所允许的最大起重质量。3.2最大工作压力maxworkpressure起重质量为最大起重质量时，液压