三阶魔方盲拧四步法公式

《三阶魔方盲拧四步法公式》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、两角翻顶层相邻两角(RUR'URU2R')(L'U'LU'L'U2L)21(L'U2LUL'UL)(RU2R'U'RU'R')12(L'U'LU'L'U2L)(RUR'URU2R')43(RU2R'U'RU'R')(L'U2LUL'UL)34顶层相对两角Z'（RUR'U')×2L2(URU'R')×2L2Z13(去Z25)Z'(URU'R')×2L2（RUR'U')×2L2Z31(去Z52)底层相邻两角(RUR'U')×2D(URU'R')×2D'58(URU'R')×2D(RUR'U')×2D'85底层相对两角(RUR'U')×2D2(URU'R')×2D26

2、8三角翻三角顺转(R'U2RUR'UR)U(RU'RURURU'R'U'R2)U123左右手公式U2+(L'U2LUL’UL)U’(RU'RURURU'R'U'R2)U’+u+＋U三角逆转(RU2R'U'RU'R')U(R2'URUR'U'R'U'R'UR')U412左右手公式(RU2R'U'RU'R')U(L'UL'U'L'U'L'ULUL2)U＋U+＋U四角翻(43)(12)F(RUR'U')2F+(RUR'U'r)(R'U)(RU'r')(43)(12)(43)(21)+(RU'U')(R'U'RUR'U')(RU'R')+(R'UR'U')(R'U')(

3、R'U)(RUR'2)(43)(21)+五角翻顶层四个角块同向1234位顺转,8位逆转[(RU'U'R'U2)(RUR'U')]×21234位逆转,7位顺转[(R'U2RU'U')(R'U'RU)]×2顶层三个角块同向1238位顺转,4位逆转[(RUR'U')(RU'U'R'U2)]×21238位逆转,4位顺转y'[(R'U'RU)(R'U2RU'U')]×2y两棱翻两相对棱13(M'U)×2M'U2(MU)×2MU2两相邻棱14(R'U2)(R2'UR'U')(R'U2)(rURU')r'四棱翻顶层十字1234(M'U)×4(MU)×42,3,5,72,3,5

4、,7(M'U)×4角块的setupmove操作集为[UDF2B2R2L2x2yz2]同层三角换1341顺x'R2D2(R'U'R)D2(R'UR')1431逆x'(RU'R)D2(R'UR)D2R2x同层四角换(13)(24)U2M2UM2U2M2UM2(12)(34)x'(RU'R'D)(RUR')u2'(R'UR)D(R'U'R)异层三角换上层相邻两角下层一角6→4→1→6(L2D'R2D)×2立体顺时针6→1→4→6(D'R2DL2)×2立体逆时针上层一角下层相邻两角2→8→5→2(L2UR2U')×2立体顺时针2→5→8→2(UR2U'L2)×2立体逆时

5、针上层相对两角下层一角换8→4→2→8[(R'FRF')×3U2]×28→2→4→8[U2(R'FRF')×3]×2先到4异层四角换两组都是对角换(13)(57)(R'FRF')×3(RF'R'F)×3斜上上层对角下层邻角(24)(78)(R'URU')(R2'URU')(RURU')(R2'URU')R2'面上对角换顶和底上下换(13)(48)(R'FRF')×3(57)(48)(RF'R'F)×3面上邻角换顶和底上下换(23)(48)(RUR'URUR'U2)×2(14)(37)[(R'U'RU')(R'U'RU'U')]×2顶层组和底换组两组相邻(48)(

6、37)B(RUR'U')×3B'(15)(48)Ry'(RUR'U')×3yR'两组相对(26)(48)B'(RUR'U')×3B前面交叉(18)(45)xU2(M2U)(M2U2)(M2U)(M2)x'一前一后(36)(48)L2(R'FRF')×3L2棱块setupmoves操作集为[UDF2B2RLM2E2S2x2yz2]在棱块的setupmoves中，自由度要比角块的setupmoves高，所以要更注意棱块的顺序，建议先U/D，然后R/L，最后是F2/B2。三棱换142逆(RU'R)(URUR)(U'R'U'R2)124顺(L’UL’)(U’L’U’L’

7、)(ULUL2’)四棱换(13)(24)M2UM2U2M2UM2（14)(23)(UR'U')(RU'R)(URU')(R'URU)(R2U')(R'U)异层换棱中圈逆1→5→3→1MU2M'U2中圈顺3→5→1→3U2MU2M'中圈(13)(57)(M2'U2)×2左斜切(13)(0A)(L2U2)×3右斜切(13)(9B)(R2U2)x3所有涉及两角两棱换的PLL都能用在奇偶处理上。必须遵循（UDF2B2R2L2）PLL公式T字（34）（24）(RUR'U')(R'F)(R2U'R'U')(RUR'F')两竖（34）（13）U'(R'URU'R2'b')x(

8、R'UR)y'(RUR'