JBT9087-1999油田用往复式油泵、注水泵.pdf

《JBT9087-1999油田用往复式油泵、注水泵.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS23.080J71中华人民共和国机械行业标准JB/T9087-1999油田用往复式油泵、注水泵Reciprocatingpumpforcrudeoil,waterinjectionusedinoilfield1999-07-12发布2000-01-01实施国家机械工业局发布JB/T908，一1999前言本标准是对ZBJ71005-88《油田用往复式油泵、注水泵基本参数》和ZBJ71019-89(油田用往复式油泵、注水泵技术条件》的修订。本标准与ZBJ71005-88,ZBJ71019-89相比，主要技术内容修改如下:—原基本参数标准中对泵的额定排出压力、额定流量和额定输人功

2、率以及泵的柱塞直径的规定作为标准的提示的附录;—取消了原基本参数标准中的附录A;—将技术要求中“泵的额定工况性能指标”、“泵运行时的噪声”和“泵的主要易损件的更换时间”按额定排出压力分档的档次“>31.5-50”分成“>31.5-40”和“>40-50"，且部分指标有所提高;—增加了试验方法方面的内容。本标准自实施之日起代替ZBJ71005-88和ZBJ71019-890本标准的附录A、附录B和附录C都是提示的附录。本标准由全国泵标准化技术委员会提出并归口。本标准负责起草单位:合肥通用机械研究所、山东潍坊生建机械厂。本标准主要起草人:谢华桂、刘树建、王录恩、刘景娥。JB/T908

3、7-1999目次1范围···，，·····················，··········，，··········，······················，···························，·········⋯⋯12引用标准····················，·············································，··································，·⋯⋯13基本参数·········，······，··，，···········，·········。·，········

4、·，··················，····，·········，··········，，··⋯⋯14技术要求·...............................................................................························⋯⋯25试验方法···············，，·，··。。·，···，······，，，，，，。·····，··。···，·，，，·······，··。·1·····，·····，，，，···.....46检验规则······················

5、···········································································⋯⋯‘⋯147标志、包装和贮存········，··..........................................··········，，·····················⋯⋯15附录A(提示的附录)基本参数·························································⋯⋯，·····....⋯⋯16附录B(提示的附录)泵的试验装置简图·.......

6、.............................................................18附录C(提示的附录)试验记录·····，···········，··································.·······一...............19中华人民共和国机械行业标准JB几9087一1999油田用往复式油泵、注水泵代替ZBJ71005-88Reciprocatingpumpforcrudeoil,ZB171019-89waterinjectionusedinoilfield1范围本标准规定了油田用往复式油泵、注水

7、泵的基本参数。技术要求，试验方法，检验规则，标志、包装及贮存。本标准适用于输送温度不高于80`C，运动粘度不超过850mm2/s，机械杂质含量不超过30mg/L,固体颗粒粒径不大于15N.m，含水量不大于2%的原油及输送温度不高于80`C，总矿化度不大于30000mg/L，机械杂质含量不超过30mg/L，固体颗粒粒径不大于15p.m的油田污水或清水的往复式油泵或注水泵(以下简称泵)o泵的额定排出压力范围为10-50MPa,额定流量范围为2-200m'/ho本标准不适用于固井、压裂