JBT5389.1-2005滚动轴承轧机用四列圆柱滚子轴承.pdf

《JBT5389.1-2005滚动轴承轧机用四列圆柱滚子轴承.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、备案号:16673-2005II中华人民共和国机械行业标准JB/T5389.1-2005代替JB/I'5389.1-1995滚动轴承轧机用四列圆柱滚子轴承Rollingbearings一Fourrowcylindricalrollerbearingsforrollingmills2005-09-23发布2006-02-01实施中华人民共和国国家发展和改革委员会发布JB/T5389.1-2005目次前言...............-.......-⋯⋯‘.⋯，二‘....................⋯⋯“.”..⋯m1范围...

2、..-.-........⋯⋯价，..二价.一一....一一一一一..一.一.一..~..一一一一一.12规范性引用文件...............一‘......⋯⋯，......一，:.”⋯，⋯⋯，.⋯⋯价..⋯，.....13符号.................一................⋯⋯“.......................⋯⋯，14主要结构类型(见图1一图3)，一‘.⋯⋯价.一一.....⋯，二，.一，一...一....一一一25代号....⋯⋯‘....................-..-.-

3、一‘.⋯‘........一，.⋯⋯价二价..一...一...一一⋯..25.1代号的构成.⋯⋯‘..⋯‘......⋯⋯‘.‘.‘二‘............⋯⋯.价，，.，二价⋯，..⋯价⋯⋯~.一25.2类型代号.⋯⋯‘.....二t............⋯⋯价.......................................⋯......25.3尺寸代号...............................................⋯⋯，..............................

4、........⋯...25.4后置代号....t..t.........................一，.......⋯⋯‘....-.......-..一，.-.⋯，.，一35.5标记示例.......................................⋯⋯‘........⋯⋯价.⋯，........36外形尺寸.⋯⋯‘.⋯⋯‘.价......................⋯⋯”..⋯⋯‘.....⋯⋯，⋯，.，二，.⋯，一37技术要求二‘..⋯⋯‘.‘..二，t..........⋯⋯‘.‘........

5、.....................⋯⋯‘.‘...-..........77.1公差..⋯‘....一，‘...-.⋯，....一，............................⋯⋯‘.⋯‘...⋯..77.2游隙...........⋯⋯‘................，.一，⋯⋯‘..⋯⋯‘.‘二‘.......⋯，二，.................87.3材料及热处理...............................................⋯⋯.‘...⋯⋯，............

6、.......97.4其他.............⋯⋯‘...................⋯⋯价⋯.，⋯⋯，，............................98检测方法⋯价.........⋯⋯价一...一一一一一..一...一一价，一.一.一一⋯⋯99检验规则....⋯⋯，..............⋯⋯，⋯⋯，，一，-...⋯，.二，二，...一，...............一910标志、防锈及包装二，.，....一，..一，-........................⋯⋯‘.⋯‘.‘...⋯⋯‘....

7、9附录A(规范性附录)商品轴承内圈技术要求⋯⋯，⋯，...⋯⋯，......................⋯...10A.I商品轴承内圈结构型式(见图A.1).......................................................⋯⋯10A.2商品轴承内圈代号.......................................⋯⋯，..........⋯⋯‘.⋯‘............10A.3商品轴承内圈外形尺寸二，......................⋯⋯，.......

8、.......⋯⋯，..........⋯⋯10A.4商品轴承内圈公差一‘一‘.......-.-...........一.⋯‘⋯⋯‘.⋯‘..........⋯⋯，......一12附录B(规范性附录)外圈油孔尺寸推荐值......