JB3380-1999木工平刨床安全.pdf

《JB3380-1999木工平刨床安全.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS79.120.01J65中华人民共和国机械行业标准JB3380-1999木工平刨床安全Woodworkingmachines-Surfaceplaningmachineswithrotarycutterblockforonesidedressing-Safety1999.10-08发布2000-03-01实施国家机械工业局发布JB3380-1999目录月U两i范围········，，·································‘.....................

2、.............··，，，···，···········，，，二12引用标准·····················，·················.················⋯⋯，···········..........··········......⋯⋯13定义与术语···················，，·········································································，·······，

3、··⋯14危险一览表，·，·················，··················，··················，····································，·····⋯⋯25安全要求和/或措施·······························，·.................................................“一”’‘”‘’‘46使用信息······························

4、一:···，···················，············，··················⋯⋯，·⋯⋯15附录A(提示的附录)防护装置的研究和设计指南·······················································一]17附录B(标准的附录)对刀具附加的要求························，···，······························，，···，，⋯⋯21附录C(提示的附录)安全下作方法·

5、····························，·······················，·············，··，，，⋯22附录D(标准的附录)机床的防护装置试验.....................................................................25附录E(标准的附录)工作台腾板的抗力试验·················。···························，··············⋯⋯26附录

6、F(提示的附录)机床噪声测定工作(运转)条件·。·····，········································，··⋯29JB3380-1999前言本标准是根据欧洲标准EN859-1997《木工机床安全木工平压刨床》对JB3380-83的修订。本标准的技术内容与EN859基本一致，增加了机床空运转噪声声压级的限值的要求。本标准与JB3380-83相比，技术内容差异较大。本标准自实施之日起代替JB3380-830本标准的附录B、附录D和附录E都是标准的附录。本标准的附录

7、A、附录C和附录F都是提示的附录。本标准由全国木工机床与刀具标准化技术委员会提出。本标准由福州木工机床研究所归口。本标准负责起草单位:福州木工机床研究所。本标准主要起草人:郑宗鉴、郑莉。本标准于1983年1月I日首次发布。中华人民共和国机械行业标准JB3380-1999木工平刨床安全代替1B3380-83Woodworkingmachines-Surfaceplaningmachineswithrotarycutterblockforonesidedressing-Safety1范围本标准规定了木

8、工平刨床(以下简称机床)的安全技术要求和检验方法。本标准适用子本标准实施日期以后生产的机床。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB/T699-1999优质碳素结构钢GB/T3770-1983木工机床噪声声功率级的测定GB/T5226.1-1996工业机械电气设备第一部分:通用技术条件GB/T9239-1988刚性转子平衡品质许用不平衡的确定G