syt6625-2005 成像测井地面仪通用技术条件

《syt6625-2005 成像测井地面仪通用技术条件》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS75.E91备案号SY中华人民共和国石油天然气行业标准SY/T6625-2005成像测井地面仪通用技术条件Generalrequirementsofimagingloggingsurfacesystem2005一07一26发布2005-11-01实施国家发展和改革委员会发布www.bzfxw.comSY/T6625-2005目次前言································································································

2、··················⋯⋯II1范围·······························································。···············································⋯⋯12规范性引用文件·························································。···。·······..........................⋯⋯13组成··················

3、·····························································································⋯⋯14要求···············································································································⋯⋯15试验方法················································

4、·························································⋯⋯46检验规则·········································································································⋯⋯67标志、标签、包装、运输、贮存·············································，·············................⋯⋯7

5、www.bzfxw.comSY/T6625-2005前言本标准由石油仪器仪表专业标准化委员会提出并归口。本标准起草单位:西安石油勘探仪器总厂。本标准主要起草人:李安宗、肖江涛、胡昌旭、王剑琴。www.bzfxw.comSY/T6625-2005成像测井地面仪通用技术条件范围本标准规定了成像测井地面仪(以下简称仪器)的组成、要求、试验方法、检验规则以及标志、标签、包装、运输和贮存。本标准适用于仪器的设计、制造及质量评价。2却范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单(

6、不包括勘误的内容)或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。GB/T191包装储运图示标志GB/T6587.2-1986电子测量仪器温度试验GB/T6587.4-1986电子测量仪器振动试验GB/T6587.5-1986电子测量仪器冲击试验GB/T6587.7-1986电子测量仪器基本安全试验SY/T5072-1998石油厢式工程车通用技术条件SY/T5132测井原始资料质量要求SY/T6235-19%数控测井地面仪通用技术条件

7、3组成仪器是计算机控制的地面成像测井系统，由下列单元组成:—计算机系统;—数据采集系统;—深度系统;—记录系统，—示波器;—供电系统;—接线控制系统;—机架;—仪器车/拖撬。4要求4.1使用功能4.1.1仪器为车载或拖撬安装的测井系统，适用于裸眼井测井和套管井测井作业。4.1.2仪器应具有的测井功能包括:a)配接井周声波成像、微电阻率扫描成像、阵列感应测井等下井仪;b)配接数控测井下井仪应按SY/T6235-19%中4.1.2的规定要求执行。www.bzfxw.comSY/T6625-20054.2外观外观要求包括:a)外表面

8、无明显划伤、裂痕、变形现象，涂覆层无气泡、脱落，金属部件不应锈蚀;b)所有开关、按键应灵活、可靠、方便，紧固件无松动，标志及指示灯清楚正确;C铭牌固定牢固，字体清晰端正。4.3环境条件4.3.1环境温度和湿度环境温度和湿度要求如下:a)贮存温度:一40℃一+600C，相对湿度