DZT0101.13-1994地质仪器仪表制造时间定额装配.pdf

《DZT0101.13-1994地质仪器仪表制造时间定额装配.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、IIZ中华人民共和国地质矿产行业标准DZ)T0101.13一94地质仪器仪表制造时间定额装配1994一01一27发布1994一12一01实施中华人民共和国地质矿产部发布目次1主题内容与适用范围···········“·“······“····“”··”····”············”······”····“·”····“······⋯⋯(1)2标准中使用的代号及含义“·”······”···“····“·······“·”····”····“”····“·”··“········”·····一(1)3时间定额的组成及计算”·”，，

2、·“·“····“··“···”·”······”···“····”·····”···········”···⋯⋯(1)4生产批量及批量系数···”·”·”···”·····”···“·”································”·····“····一(3)5紧固件时间定额·········””······”····”·“······”····”·”····”····““····“·”····”············“”·(3)6沾胶、粘接时间定额“·····““·······”·”·····””·····“

3、······”“······”·一:’········”·····-····，.⋯(13)7轴孔铆接时间定额···““····“·”······“·”····“·”·”·“·”·······”··“··················”·····一(14)8导线加工时间定额”···”·”·····“·····“·····“·“·····”···”·”···“·····”···”·”·····”·”一(24)9元器件加工时间定额“····“·“·”···“·”····””·”·“·”·”···“·····”···”·”···“·”···

4、“·“·，’·“⋯(36)10导线、元器件焊接加工时间定额................................................................................(50)11绕制线圈时间定额···”，··“··“‘·····“·.................................“······“·“····”········”·⋯(59)12取、放时间定额···“···‘···“········“········“”·········”····“·······”··

5、·····”·······”·······”···⋯⋯(70)13平面运输时间定额····“·”···”·”·”··‘”·”···“·”···“·“···········”···“·”··········一(71)14清洁时间定额·“········.........................................................................................(72)附录A计算示例(参考件)······”···“·”·······“·”······”····“·”···

6、·“·”·············”·······”⋯⋯(73)附录B常用线径、电阻值对照表〔参考件》“·”·····“····“·”·····””·····“”，···············”·····一‘二(76)附录C索引(参考件)····””······”······一，...................................................................(80)中华人民共和国地质矿产行业标准DZ/T0101.13一94地质仪器仪表制造时间定额代粉DZ57.14-87装配主题内

7、容与适用范围本标准规定了地质仪器仪表行业装配的时间定额。本标准适用于地质仪器仪表制造行业生产的各类产品的装配。标准中时间单位为“秒”(s)，个别以“分”(min)为单位处在文中给出;长度单位为“毫米”(mm)。标准中使用的代号及含义(见表1)表1代号含义T:单件时间定额Tas基本作业时间及辅助作业时间K布休系数D直径(线束外径)L长度d线径或套管外径N线匝数3时间定额的组成及计算3.1时间定额的组成装配时间由四部分组成:二准备、结束时间;七.布置工作地时间，c.休息与生理需要时间，d作业时间:包括基本作业时间(剪、焊、弯、绕、装、拧和

8、铆)及辅助作业时间(找线头、拿放工具、垫圈和螺钉等)。32‘准备、结束时间定额(见表2)-中华人民共和国地质矿产部1994一01一27批准1994一12一01实施Dz/T0101.13一94表2口nn卜复杂钳电组调序号工