汽车行业整车标准：QC T 645-2005 清障车.pdf

《汽车行业整车标准：QC T 645-2005 清障车.pdf》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、中华少味民共和国汽车行业标准QC/T645一一2005代替QC/T645-200017全清1延寻车Towtruck2005-07-26发布2006-01-01实施巨J箕蔑2万A和1已定军互霎冬石改声鉴参发布中华人民共和国国家发展和改革委员会月匕公口2005年第46号国家发展改革委批准《钢质管道单层熔结环氧粉末外涂层技术规范》等204项行业标准(标准编号、名称及实施日期见附件)，其中石油天然气行业标准87项、汽车行业标准9项、黑色冶金行业标准55项、轻工行业标准43项、锅炉压力容器行业标准10项;批准《JB4732-1995<钢制压力容器分析设计标准>)1项锅炉压力

2、容器行业标准修改单，现予公布，《钢制压力容器分析设计标准》行业标准修改单自2005年10月1日起实施。附件:9项汽车行业标准编号、名称及实施日期中华人民共和国国家发展和改革委员会-:100五年七月二十六日附件;9项汽车行业标准编号、名称及实施日期序号标准编号标准名称被代替标准编号实施日期88QC/T645-2005清障车QC/T645-20002006-01-0189QC/T733-2005沙漠车辆2006-01-01摩托车和轻便摩托车发动机密封90QC/T734-20052006-01-01性能技术要求与试验方法摩托车和轻便摩托车方向把角度91QC/T735-2

3、0052006-01-01和宽度尺寸轿车发动机钢带组合油环技术条92QC/T736-20052006-01-01件93QC/T737-2005轿车发动机铸铁活塞环技术条件2006-01-01摩托车和轻便摩托车制动器台架94QC/T654-2005QC/T654-20002006-01-01试验方法摩托车和轻便摩托车制动器技术95QC/T655-2005QC/T655-20002006-01-01条件96QC/T738-2005轻便摩托车用电喇叭技术条件2006-01-01OUT645-2005目次前言································

4、························································。。，，，，·，，·，，，，···，⋯⋯11范围············································································································⋯⋯12规范性引用文件·················。。····，·。。···。······。，。·，，，，···，，，····，······························

5、·⋯⋯13术语和定义··································································································⋯⋯14要求·。····。·····················。··，···，，，，，·，·，，···············，············································⋯⋯35试验方法一6检验规则7标志和使用说明书···········································

6、··················，·，，·················⋯⋯，二，.，78随车文件、运输和贮存·······································································.............⋯⋯8附录A(规范性附录)专用装置试验记录表·········，，······。·······一，，，二，二，...............⋯⋯9附录B(规范性附录)故障分类························································

7、···················⋯⋯I1附录C(规范性附录)清障车最大托举质量计算规范···············，，···，，，，·······················⋯⋯12QC/T645-20059(J言本标准与QC/T645-200(〕相比，主要修订内容如下:—修改了“额定托举质量”的定义。—增加了“最大托举质量”的定义。—增加了清障车轴荷及质量的要求。—增加了规范性附录Co本标准的附录A、附录B和附录C为规范性附录。本标准由全国汽车标准化技术委员会提出。本标准由全国汽车标准化技术委员会归口。本标准起草单位:广东粤海汽车有限公司、汉阳专用汽

8、车研究所。