gb20007-2005 木工机床安全 单轴铣床

《gb20007-2005 木工机床安全 单轴铣床》由会员上传分享，免费在线阅读，更多相关内容在行业资料-天天文库。

1、ICS79.120.10765中华人民共和国国家标准GB20007-2005木工机床安全单轴铣床Safetyofwoodworkingmachines-Singlespindlemouldingmachines2005-12-01发布2006-07-01实施中华人民共和国国家质量监督检验检疫总局发布中国国家标准化管理委员会GB20007-2005目次皿前言11范围12规范性引用文件2术语和定义6危险一览表85安全要求和/或措施·95.1控制和指令装置·9控制系统的安全性和可靠性95.1.2操纵器的位置⋯⋯l05.

2、1.3起动··⋯⋯l0S.1.4正常停止105.1.5紧急停止n5.1.6模式选择n5.1.7转速改变15.1.8动力源故障⋯n5.1.9控制电路故障n5.2机械危险的防护n5_2稳定险................n5.2.2运转中的断裂危险二n5.2.3刀具和刀夹的结构二145.2.4制动··········....⋯⋯155.2.5将抛射的可能性和影响降低到最小的装置······⋯⋯155.2.6工件的支承与导向装置····，·························⋯⋯175.2.7进人运动零部

3、件的防护·····························⋯⋯205.2.8夹紧装置，···········⋯⋯“““““‘’205.2.9带防护功能的工作装置21非机械危险的防护二2153火和爆炸····⋯⋯215.3.2噪声···········，···....⋯⋯，215.3.3木屑、粉尘和有害气体的排放215.3.4电气设备·················⋯⋯“““‘’215.3.5人类工效学和安全搬运的要求25.3.6照明·················....⋯⋯25.3.7气动装置·⋯⋯

4、25.3.8液压装置·⋯⋯25.3.9热危险二，.，，..⋯，25.3.10危险材料咒5.3.11振动·⋯GB20007-20055.3.12辐射·······················································································，，·············⋯⋯225.3.13激光··············································，·························

5、···························，··⋯⋯225.3.14静电············································，························································⋯⋯225.3.15装配误差·······································，··········································，·······......⋯⋯225.

6、3.16能量输送的切断·······················································································⋯⋯225.3.17维修···········，··································，·······················································⋯⋯226使用信息······································

7、·······，·，·········································，··········，····⋯⋯226.1警告装置·····························································，········································⋯⋯226.2标志······································································

8、······································⋯⋯226.3使用说明书·····································，·····················································，······⋯⋯，23附录A(规范性附录)最大主轴转速的确定···············